PVC Ceiling Tiles 2x2 - PVC Laminated Gypsum Board

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

PVC Gypsum Board, , PVC Laminated Gypsum Board

4.Detailed Specification

PVC Gypsum Board, , PVC Laminated Gypsum Board

• DETALED PRODUCTION DESCRPTION

1. name: PVC Gypsum Board, , pvc laminated gypsum board, pvc gypsum ceiling,Pvc gypsum ceiling board

2.size: 595mmx595mm;600mmx600mm;603mmx603mm; 605mmx605mm;

595mmx1195mm;600mmx1200mm;603mmx1212mm;605mmx1210mm

3. thickness: 7mm, 7.5mm, 8mm, 9mm

4 surface coverd by pvc foils

5 back with aluminum foils.

6.the four edges are covered by tapes

7.easy to install and easy to clean

8. more than 100 kinds of designs: 154 ,572, 996;9025-1, 9031-4, D7,D8;R112, JM572, R121

9. modern decoration

10.tension strong, moistureproof, heat-preventing, ametabolic

•APPLICATION

1) Supermarket, marketplace

2) Underground, air port, bus station

3) Hall, corridor

4) Hotel, restaurant, kitchen

5) School, office, meeting room ,hospital etc.

Q:What are the specific national standards for pvc? The: Want to figure out, PP forum, a lot of PVC film information, there are a lot of PVC film and printing bag to do friends, many of which are in the first line operator, responsible for the technology. There are also PVC particles

Q:PP and PVC sheet, which performance is good? What is the lower price Engineering design is the PP board, if it is in the acidic environment, PVC board can replace the PP board?: Mainly to see you use the direction of the. PVC mechanical properties, excellent electrical properties, strong acid and alkali resistance, chemical stability, but low softening point. Suitable for the production of thin, wire and cable insulation, seals and so on. PP its excellent electrical properties, can be used as high-temperature insulation materials, high hardness, high hardness. It can be said that the market is usually two mixed applications. The price is high PP board. PP can replace the PVC board, but in general or PVC board acid good

Q:The building codes where I live are based on NEC codes. They're really hard to understand as a non-electrician.: You only need conduit below the bottom of the joists or running down a concrete or block wall. If the NM cable is run along the joist or through holes in the joist if run across joists, no conduit needed. It does need to be stapled or otherwise supported every 4 feet. Where you need conduit, flex is okay.

Q:Pvc board ceiling installation method which know? How much is the installation cost?: When installing the PVC gusset, the secondary bone should be straightened. Buckle plate should be flat, not warping, ceiling flat surface error can not exceed 5mm.

Q:Uv printer hit pvc board why a scraping off Before the scraping is very good scraping off, and now a nail plan, plans to fall out: Can be analyzed from two aspects: Ink and coating problems (this can only be resolved through the sale) PVC board problem (this can ask the supplier, the board and before there is no difference, because the higher the density of printed materials, UV ink adhesion worse)

Q:Often use a black PVC bag to bathe the bath is harmful to the body?: There, pvc which contains chlorine, received ultraviolet radiation will be released within a carcinogen

Q:Pvc board how to install curved curtains: Electric track is customized directly from the manufacturers, requiring accurate size, can not turn right angle or bend too fast, and the width of the curtain box requirements.

Q:Whenever we run hot water in the kitchen (faucet or dishwasher), a loud knocking noise comes from the PVC pipes in the basement. It seems to be coming from the main drain pipe which is about 3 or 4 inches in diameter, and it knocks right along the ceiling joists. After a few minutes the knocking stops. Any suggestions?: Same as with copper - install an air surge valve

Q:MY girlfriend is using a 10' piece of 4 PVC to make a cat tree. About half way up, we put a wye joint in to make a shelf. The post will be fixed to the floor and ceiling. The problem is that the post flexes back and forth at the wye joint. I used silicone, but it didn't help the movement. Is there some kind of expanding caulk I could use? Any other ideas on how to keep it stable?: I'm guessing that you haven't installed it yet? When you attach it firmly to both the floor and ceiling, it should become very stable. I don't think that you'll have to add any structure. (Unless she has a really big cat...)

Q:Laser cutting can cut PVC board: Can cut, but the general manufacturers are not recommended to cut PVC, will produce toxic gases.

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range