Professional Stainless Steel Multifunction Folding Plier 11 in 1 for Outdoor and Camping

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Professional Stainless Steel Multifunction Folding Plier 11 in 1 for Outdoor and Camping

Q: What is the water nozzle?: Nozzle refers to the mold products, mold reserved for the mold into the raw material of the hole, the workpiece after casting, the casting part of the link on the channel called "water gate", you need to cut down.

Q: The current connection with triangle three-phase motor clamp meter measured the phase current and line current: Current clamp meter measuring three-phase motor delta connection is phase current, current, it from one phase to another phase from the back, not as light from the phase from the zero line back, so you are measured by the phase current.

Q: What is the brake caliper of the car?: There are two kinds of brakes in the car, one is disc brake before and after the other, and the other is drum brake in front and rear hours.

Q: The first use of forceps, often can not move the pipe clamp, ask how to correctly use the wrench?: Use a pipe wrench, should first check whether the firm fixation pins, pliers, pliers handle has no cracks, cracks can not be used; the smaller pipe, not too much force, not with a boosting rod, can not use a pipe wrench as a hammer or crowbar. In addition, wash the grease immediately after use and apply the butter to prevent the rotating nut from rusting and return to the tool carrier or inside the tool room.

Q: What is the automatic stripping pliers: The principle and method of use: as shown in the figure for the wire stripping pliers mechanism, when the handle grip pliers, in spring is firstly compressed, making the clamping mechanism to wire. At this time, the shear mechanism does not move due to the action of the torsion spring 1. When the tightening mechanism clamps the electric wire completely, the force acting on the torsion spring 1 gradually changes, so that the torsional spring 1 starts to deform, so that the shearing mechanism starts to work. At this time, the force of the torsion spring 2 is not enough to make the clamping mechanism separate from the cutting mechanism, and the shearing mechanism completely cuts the wire skin and the cutting mechanism is clamped. The 2 torsion spring force increases, when the torsion spring two forces to a certain extent, the torsion spring 2 separate clamping mechanism and the shear deformation mechanism, the insulation wire and the wire is cut apart, so as to achieve the purpose of stripping.

Q: What's the name of the pipe on the pliers table?: Named pipe [material] drop forged or cast steel. [introduction] pipe fitting is used to connect the fastening or loosening tool. The utility model comprises a clamp handle and a chain hinged at one end with the clamp handle, and the front end of the pliers handle is provided with teeth which are meshed with the chain.

Q: How do I use the hydraulic tongs?: Unscrew the pressure relief valve or pressure discharge valve needle handle rotation, until the piston cylinder completely back, the complete cutting pliers: hard and soft and hard steel scissors can shear steel strand (overhead line) copper cable, copper cable can only shear soft, working steps and crimping pliers, just some cutting pliers without safety valve (relief valve), so in the cable (steel) cut, do not continue to handle pressure. Hand hydraulic pump: used to fit split pressure connections, shear heads used.

Q: Is the nose pliers the same as the water jet pliers?: Not the same, the nozzle blade is thin, relatively sharp, can only cut thin copper wire and plastic, rubber and other materials, cut the copper wire after the incision is flat.

Q: What's the hydraulic clamp for?: Because it can provide more clamping force than the manual and lever force, so it can be used only by hand, which can not be done. For example, flat steel tubes can be clamped to block leakage and cut steel bars.

Q: With the method of leakage fault check line clamp meter: If a net current is detected between the supply current and the return current, the nature of the load and circuit need to be taken into account.

Send your message to us

*Email

*TEL

*Quantity

*Unit