MILLING TOOTH WIRE STRIPPER HAND TOOLS 109
- Ref Price:
-
- Loading Port:
- Ningbo
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 3000 pc
- Supply Capability:
- 20000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specification
MODEL:109
SPEC:6"
QUANTITY PER CARTON(PCS):12/120
G.W./N.W.(KG):21/20
PACK.DIEM(CM):38*25*45
WIRE STRIPPER
Key specification:
1.cut any cleanly strips electrical wire from 10 to 22 gauge
Insert tip of wire into marked holes to determine the size of the wire to be stripped
Squeeze the handle to strip easily and without nicking the wire
2.crimps both insulated and non-insulated ignition terminals
3.tool has black oxide finish for rust resistance
4.Vinyl clad cushion grip handles insulate as well as provide comfort of use
Using the method of the wire stripping pliers
All by hand if the wire stripping pliers groove is then a simple select wire size cut a pull on the line. If and oblique mouth clamp like it by hand, clip to a certain strength, a pull on the line.
Key points:
according to the diameter of the wire, the wire stripper blade aperture
1.According to the thickness of the cable type, select the corresponding stripping knife
2.The cable will be ready in the middle stripping tool blade, to choose a good length of wire stripping
3.Hold the stripping tool handle, cable clip, cable force slowly slowly peeling off the outer skin
4.Loosen the tool handle, then remove the cable, cable metal neatly exposed outside, the rest of the plastic insulation intact.
- Q: How to use a clamp meter right? Use should pay attention to what matters?
- 1 before measuring, should first check whether intact core rubber insulated clamp. The jaw should be clean and free of rust, and there is no obvious gap after closure.2 when measuring, the current should be measured and the proper range should be chosen. If you can't estimate, you can select a larger number of courses, then reduce the number of files to the appropriate gear. When converting the range gear, it must be done in the case of no electricity or under the opening of the jaw so as not to damage the meter.3 measurement, the measured wire should be placed in the middle of the jaw with jaw, face such as noise, should be re opening and closing time, still have the noise, should handle the joint surface, in order to make accurate readings. In addition, not at the same time around the two wires.4 measurement of the electric current is less than 5A, to get more accurate readings, when conditions permit, the wire around a few more laps, into the jaw measurement, the actual current value should be put into the meter reading divided by the number of jaw root wire.5 before and after each measurement, the switch of regulating current range should be placed in the most advanced position, so as not to damage the meter when measuring the frequency range without selecting the next time.
- Q: Application and working principle of the clamp current meter
- Its working principle is as follows:Clamp meter is composed of a current transformer and current meter assembly. The iron core of the current transformer can be opened when the wrench is tightened; the wire through which the current is measured can be cut through the opening of the iron core without cutting off, and when the wrench is released, the iron core is closed. Through the test circuit of the core, the wire becomes the primary coil of the current transformer, in which the current is induced in the two coil through the current. A current meter connected with the two coil is used to indicate the current of the line to be measured. A table can shift through the switch, the scale change. But the switch is not allowed to operate when charged. Clamp meter general accuracy is not high, usually 2.5 ~ 5. In order to facilitate the use of the table there are different ranges of switching switches for measuring different levels of current and voltage measurement function.
- Q: What is the holding technique of sterile holding forceps in proper nursing operation?
- When the sterile forceps is taken, the end of the forceps is closed downward and can not be touched. The edge of the collector's mouth of the large website is put back into the container immediately after use.5. indicate the date and time of opening.
- Q: What kind of pliers is this? What's the exact model? Can I cut the bar?
- [functional characteristics]1, forgings2, small wire tools, clockwork attachment, with one hand can easily cut off.3, blade forging special steel, because it is locking mechanism attachment, safe to use, easy to carry.4. Cut off material object: low carbon steel wire rod hardness is below HRB80
- Q: Can the crystal head of network cable be fitted with ordinary pliers?
- Can not but very laborious, the lines straightened out, with scissors, and then stuffed into the crystal head, looking for a flat screwdriver, pressed downwards! And then it's ok! You can try it, I used it!
- Q: Nail clippers rusty, how to rust?
- Take the swab and wipe it with a toilet
- Q: Can you use an old vise to cut an electric 220V wire?
- Matters needing attention(1) no ordinary pliers are used for live work; live working, please use telecommunication pliers;(2) when shearing tight metal wires, protective measures shall be taken to prevent the metal wires from being sheared;(3) wire cutters can not be used as percussion tools.
- Q: A multimeter to measure power
- A table can shift through the switch, the scale change. But the switch is not allowed to operate when charged. Clamp meter general accuracy is not high, usually 2.5 ~ 5. In order to facilitate the use of the table there are different ranges of switching switches for measuring different levels of current and voltage measurement function.
- Q: How do you cut the wire with pliers?
- Put the wire on the inside edge of the pliers, and the clamp is broken
- Q: What does "cut in" mean?
- Clamping type: the connection of pressure vessel and shell is generally divided into placing connection, plug-in connection, embedded connecting pipe and so on. The embedded nozzle has the characteristics of intensive reinforcement, and the reinforcing metal can be concentrated at the joint of the connecting pipe and the shell. A joint that forges a small butt joint and forms a butt weld with the cylinder head.
Send your message to us
MILLING TOOTH WIRE STRIPPER HAND TOOLS 109
- Ref Price:
-
- Loading Port:
- Ningbo
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 3000 pc
- Supply Capability:
- 20000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
