Packing and Lamination Film-Aluminum Foil/Polyethylene
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 10000 m²
- Supply Capability:
- 1000000 m²/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specification
Product Structure
Widely used for laminating with EPE insulation, Bubble insulation, woven fabric insulation, etc
● Aluminum foil – LDPE
● Aluminum foil- PET- LDPE
● Clear Transparent PET-Aluminum foil – LDPE
● Aluminum foil-Metallized PET- LDPE
● Metallized PET- LDPE
Product Application
Widely used for laminating with EPE insulation, Bubble insulation, woven fabric insulation, etc
Product Advantage
Light weight
• High manufacturing accuracy
• High strength
• Small inertia resistance
• Strong heat dissipation ability
• Good visual effect
• High reflective insulation
• Heat resistant, water proof, stable at high temperature;
• Environmentally friendly, no smell and not-toxic;
• Smooth and clear surface;
Product Packing
1. Waterproof paper then PVC shrinking Film
2. Kraft paper only
3. Woven cloth
4. Kraft paper or Water Proof Film then Metal/wooden pallet
5. (Also as your request. )
Product Remarks
1. The data above are typical results and subject to change without notice.
2. Tolerance: Weight and Thickness: ±10%; Width: ±3mm;
Length: Cut Roll & Log Roll ±0.3m, Jumbo Roll ±0.5%.
3. The products should be stored at room temperature and kept from wet and heat source.
4. It is essential, as with all pressure-sensitive tapes, that the surface to which the tape is applied must be clean, dry, and free of grease and oil.
5. The user should take test and do trial-application on the above products before coming into application so as to witness and ensure suitability for user’s special purpose and technique.
Product Data Sheet
PROPERTIES | UNIT | VALUE | TEST METHOD |
Basic weight | gsm | 43.5 | ASTM D646 |
Thickness | mic | 33.2 | ASTM D646 |
Tensile strength: M. D. X. D. | N/15mm | 23.5 33.5 | ASTM D882 |
Delaminating Values | N/15mm | 2.5 | ASTM D904 |
Reflectivity of foil surface | % | 95 | ---------- |
Temp. Resistance | -40°C 130°C | No Delamination No Delamination | ASTM C1263 |
Water vapor permanence | ng/N.s | 1.15 | ASTM E-96 |
Product Picture
FAQ
1. What is the product keeping conditions?
The Aluminum Foil Facing should be stored at room temperature and kept from wet and heat source.
2. What is the guarantee years of the products？
We have established the international advanced quality management system，every link from raw material to final product we have strict quality test；We resolutely put an end to unqualified products flowing into the market. At the same time, we will provide necessary follow-up service assurance.
3. What is the delivery time of the order?
In the purchase of product within four working days, we will arrange the factory delivery as soon as possible. The specific time of receiving is related to the state and position of customers. Commonly 7 to 10 working days can be served.
- Q: Which plastic film is more suitable for making heat shrinkable labels?
- Need to blank, QS logo for color requirements, bar code is required for the blank area, height can be adjusted. But not less than GB 1/3.
- Q: Such equipment is used for cutting paper?
- Then put the plastic film along the width direction of fiber board wrapped up, usually wrapped around twenty to fifty layers, the thickness of plastic film and video.
- Q: What material is the film on the waterproof roll? What's your name?
- The rigid surface layer (usually 40mm thick fine stone concrete) there will be deformation of thermal expansion and contraction, if the waterproof layer and the rigid layer is very good, the rigid layer deformation will affect the waterproof layer with deformation, it may produce direct damage crack or long-term fatigue on the waterproof layer, so the isolation layer has a set of functions in the slip two tectonic layers;
- Q: Is it beneficial or harmful to wrap trees in plastic film?
- Wrapped grass first with straw or directly to the trunk wrapped with straw tied membrane, and then fixed on the trunk with fine grass. Then with the water or spray will spray wet straw, can also be careless or straw soaked and package. The plastic bag in the careless orstraw strapping on the trunk will last film. The lower part of the trunk is close to the soil ball to spread the film. After the foundation is covered with soil, it is covered with plastic film. Plastic film surrounding soil pressure, so that the use of soil temperature regulation, to ensure that the parcel trunk space is sufficient temperature and humidity, and avoid the work of adding water.
- Q: Keyboard circuit board, film paper and rubber strip, how is it installed?
- The rubber strip is pressed on the outside of the film. Generally, the rubber strip is placed on the cover, then the membrane is placed, and then the circuit board is inserted. Then the screw is screwed down to the circuit board, so that it is compressed.
- Q: Why should a plastic film be affixed after the concrete has been poured?
- According to thermodynamic calculation, and the concrete surface temperature difference is not greater than 25 degrees, concrete pouring time after surface covered with a layer of plastic film insulation, timely prevent the conservation of water caused by excessive temperature difference between inside and outside the concrete temperature crack.
- Q: Why should a plastic film be added to the new cement road?
- The new cement road needs a layer of plastic film for better maintenance.
- Q: Why plastic film greenhouse can keep warm?
- Because the heat is hard to escape through the plastic film, the temperature difference between the upper and the lower of the greenhouse can not be enlarged, and the convection is very small, so that the heat can be kept warm. The key here is the plastic film is very similar to shun donkey, sun radiation from the inside, with stubble, almost without shelter; and the heat from the inside out is the inverse stubble, resulting in heat insulation.
- Q: FFS plastic film bags are injection type?
- Mainly uses a large single screw extruder and single monolayer extruder head configuration, three layer co extrusion equipment is divided into three layers of laminated film blowing head of three smaller extruder and configuration can be automatically adjusted, other devices on the same.
- Q: Why should a plastic film be covered after civil construction?What's the point? Do you have any requirements for plastic film?
- The plastic film has no special requirements, as long as the cover to prevent water evaporation. In the cold season construction to cover the mats and other things to keep the temperature.
Send your message to us
Packing and Lamination Film-Aluminum Foil/Polyethylene
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 10000 m²
- Supply Capability:
- 1000000 m²/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
