LED Infrared Light T8 Tube 12W/3W Sensor Tube 1.2m

LED Infrared Light T8 Tube 12W/3W Sensor Tube 1.2m

Ref Price:: $14.90 / pc

Loading Port:: Shenzhen

Payment Terms:: TT

Min Order Qty:: 10 Pcs pc

Supply Capability:: 100000 Pcs Per Month pc/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

LED T8 Integrated Tube SMD Chip High Bright 1.2M 18W

T5 Led Tube Light Fixture

8W 10W 12W 14W 16W 18W 20W 1200M 2Feet 4 Feet Smd2835 T8 Light Led Tube

Tuv-Ce Approved Cree Epistar Chip 2835Smd T8 Led Tube Light

LED Lighting Glass 600mm T5 Tube Lighting

LED Lighting Integrated Tube5 CE RoHS TUV ETL t5 Bracket Lamp

Tube Japan Tube Hot Tube LED Tube Light LED 4 Tube

T5 LED Tube with CE ROHS UL Certification

LED Infrared Light T8 Tube 12W/3W Sensor Tube 1.2m 1. This product meets the standard of CE certification.
2. With internal No-isolated power supply.
3. Round and the elliptical tube are available.
4. Use the most mature international well-known LEDSMD2865 as the light source, which can ensure the led tub35 as the light source, which can ensure the led tube brightness and long lifetime, also can reduce the light decay.
5. Use the high quality aluminum PCB for LED’s better heat dissipation.
6. High-grade PC cover with nice light transmittance(> 95%),Transparent PC cover and frosted PC cover are available.
7. 180 degrees beam angle makes the lighting effect better.
8. CRI(standard products)>70,it can be over 80 if required.
9. Ambient temperature:-20°C-40°C, surface temperature: 42°C-45°C
10. No mercury, lead or other hazardous materials; no radiation, no electromagnetic radiation, no frequency flash, instant start up, no hurting eyes.
Applications:
Replacement for conventional fluorescent tubes:
1. Hotels
2. Conference/ meeting room
3. Commercial Complexes
4. Residential/ Institution Buildings
5. Schools, colleges & Universities
6. Hospitals General li

Q: Are led fluorescent tubes not available for lighting?: It is also possible to use a stent without a stent, usually with a negative level on the positive side of the connection

Q: Can the LED tube be installed as a general lamp holder? It won't burn easily: Cannot be installed directly, need to change internal wiring. Leds are not the same as the traditional lamp tubes, which have the power supply inside the LED tube, and the input voltage at both ends of the tube is 220V. The traditional lamp power source is placed outside, and the voltage at both ends of the lamp is as high as a few hundred volts. If the LED tube is directly installed, it will burn down the power in the LED lamp tube because of the hundreds of volts of voltage that the original fluorescent lamp's ballast outputs. 3, therefore, the LED light tube cannot be installed directly in the traditional fluorescent tubes, the need to remove the internal ballast, then change the input at the ends of the line. LED bulbs are usually two incoming lines, one firewire and one zero line.

Q: How long does the energy-saving daylight lamp tube change?: Fluorescent lamp use time is long, the brightness is low is normal [because of the efficiency of fluorescent powder is reduced, cause lamp tube brightness drops]. The general store is not convenient to replace at any time, it is better to replace it at once. If you increase the density of the light, the light efficiency of the tube will not increase much, and the energy will increase with the opening of the tube, a little waste. A one-time change is a lot of input and a lot of it is compared to the actual computation.

Q: What causes the red light on both ends: Several reasons, the inductance ballast may be neon bulb breakdown short circuit, the shunt capacitance in the starter or not the capacitance may be a bubble in the bimetallic strip jump is not opened, and at the ends of the electronic ballast and the bulb is a resonant capacitance breakdown short circuit, the above cases, red middle not light on both ends of the tube, and is a situation in the middle will be bright, but is not stable, and not the brightest state, is more obvious black on both ends of the lamp aging, conduction resistance big cause filament at start preheating condition at both ends and a red glow, especially the inductance ballast lamp aging at low temperature state is more obvious when starting, the electronic ballast will have original power rectifier filter circuit damage (400 v / 4.7 ~ 10 uf or diode IN4007), also happen when the result in low voltage power supply, replace the corresponding parts.

Q: A 36w daylight light with a watt LED lamp?: Again, the traditional fluorescent lamp is an all-round (360 °), a most of the waste in the back, actually the total quantity of light for lighting only 60% ~ 65%; General LED fluorescent light emitting Angle 120 ° ~ 180 °, is essentially effective light. Calculate this method.

Q: If the body is accidentally broken, will it be electrocuted?: You don't touch the electrodes without touching the two electrodes. But be careful when you break

Q: What's the matter with the light bulbs?: Tungsten electrode, turn off the light inside, inside with mercury vapour, through high pressure mercury vapour breakdown, and consumption of tungsten electrode, electric light, may be a poor contact circuit aging or light foot, if end black gathered themselves together, and it is also possible that a serious of tungsten electrode burning, still hope electrician check and to avoid an accident!

Q: I have LED lights on the fluorescent lamp, and I tested it when I was running five times a dc, and four LED lights were very bright and hot,: Let's say a light bead is working at 3v voltage and the current is 300ma. To get it to 3.1 volts, the current can reach 400ma. 220v market volatility is large (200-250) sometimes higher. At the very least, you need to add resistance.

Q: The ledt8 lamp is used for the light bulb: The average LED T8 lamp is based on the number of lamps in the wattage, and the average light bulb is 0.5 w, and according to the wattage, you know how many lamps are there.

Q: How does the T8LED light tube replace the fluorescent lamp tube: I just changed it. I bought a LEDT8 type of fluorescent tube 1 meter 2. 16 watts is basically equivalent to the ordinary energy-saving fluorescent tube 60 watts. It's very bright and bright, and you don't need a flash. But there are brands that don't have to take down the ballast, and you have to consult the person who sells your LED tube. The ballast and the regenerator are broken down, and the different brands are different.

Focus on environmentally friendly LED intelligent lighting products are obtaining CE, ROHS, CCC and other domestic and international authoritative certification; product sales in the domestic market to maintain continuous growth, and exported to Europe, America, Southeast Asia more than 10 countries.

1. Manufacturer Overview

Location	Shenzhen,China
Year Established	2011
Annual Output Value
Main Markets	Mid East；Western Europe
Company Certifications

2. Manufacturer Certificates

a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability

a) Trade Capacity
Nearest Port	Dongguan
Export Percentage
No.of Employees in Trade Department	50-100 People
Language Spoken:	Chinese
b) Factory Information
Factory Size:	Above 1,500 square meters
No. of Production Lines	About 5
Contract Manufacturing	OEM Service Offered；Design Service Offered
Product Price Range	Cheap