K Series 2-3.5T I.C. Counterbalanced Forklift Trucks

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Model		CPC20	CPCD20	CPC25	CPCD25	CPC30	CPCD30	CPC35	CPCD35
Load capacity	kg	2000		2500		3000		3500
Power type		Diesel
Overall length (without forks)	mm	2502		2576		2682		2693
Max. lifting height	mm	3000
Load center	mm	500
Overall width	mm	1170		1170		1225		1225
Overall height (overhead guard)	mm	2070		2070		2090		2090
Min. turning radius （outside）	mm	2170		2240		2400		2420
Max. travel speed (with/without load)	km/h	17/19		17/19		18/19		19/19
Service weight	kg	3364		3680		4270		4700

Q: How to solve the oil spill?: Fix the main bearing in time. When the main bearing and shaft neck fit clearance is too large, before and after the sealing of the oil seal for crankshaft impact could lose caused by the oil from the crankshaft head leakage, or to the penetration of the clutch oil, thus pollution lining cause skid, job failure. Avoid the one-way valve and the ventilatory valve. This type of valve hole blocking easy cause box shell temperature, pressure, piston motion resistance, fuel consumption increase, oil and gas is full of the whole space, lubricating oil consumption increase and change cycle shortened. Properly handle all kinds of tubing joint seals. Tighten and press the nuts to seal and seal, after sealing or sealing the thin copper leather on two cones. Avoid hubcaps. Cavity should be adopted for the lubrication (namely adequate lubrication), dredge vent, the rational use of braking, strictly choose the high quality parts, and assembly and adjustment according to the process specification. Hopefully, the above points will help you to solve similar problems.

Q: How do you drive the forklift: (1) check the vehicle Before (1) forklifts, the appearance should be inspected, and the fuel, lubricating oil and cooling water should be added. (2) check start-up, operation and braking performance. (3) check the lighting and sound signal to be fully effective. (4) the forklift should check the pressure and the temperature is normal. (5) after the operation of the forklift truck, it should also check the leak and replace the sealing part in time. (6) the electric cylinder forklift should check the contents of the electric car and inspect the circuit of the electric bottle forklift.

Q: Why are there two kinds of special equipment operators: The forklift belongs to the bureau of quality and technical supervision, and of course the special equipment operator's certificate is good. Your homework must be a forklift driver. It's a special equipment operator, it's not something else.

Q: What should 80V force forklift voltage current be?: Voltage 380, the current changes with charge time, from strong to weak. The internal combustion forklift is divided into regular internal combustion forklift, heavy lift truck, container forklift truck and side forklift truck. Internal-combustion forklift

Q: How many ways to push the forklift truck?: commonly used ordinary internal-combustion forklift diesel, gasoline, liquefied petroleum gas or natural gas engine as power, load capacity of 1.2 8.0 tons, general operation channel width of 3.5-5.0 meters, emissions and noise into consideration, usually used in outdoor, workshops or other places with special requirements for emissions and noise did not.

Q: What do you mean by the center spacing of the load on an electric forklift?: Another thing is that electric forklifts are generally balanced, which is used to boost goods. The standard three-ton electric forklift, for example, is fitted with a 1070mm cargo fork, and its payload center is about half the length of the fork, which is 535mm. If the length of the goods is within 1070, there is no problem of lifting the three tons of goods. But if the goods length is 1.6 meters, so the location of the center of the goods is in 0.8 meters, so beyond the electric forklift truck loading the position of the center distance of 0.535 meters, 26.5 cm, according to the lever principle, by this time if you have any 3 tons goods, so use this 3 tons of electric forklift is exhausting. It is possible that the rear portion of the electric forklift is lifted by the weight of the cargo.

Q: A manual forklift oil leak, what if you can't get up?: Internal leakage (1) there is too much friction between the stem and the valve body Multiple directional control valve hoisting and tilt on the stem of each have three groove, groove and oil that can be switched on or off oil, change the way to work. Good distributing valve clearance between the valve stem and valve body is small, the spill is few, so the hydraulic cylinder down or tilt volume is small, do not affect work. But when wear clearance is too large, under the pressure of the hydraulic oil pump at work to produce, can cause work in oil or oil spill oil and the oil return tao, automatic back to the tank. The reason is mainly, because of the distributing valve use for a long time or the oil not clean accelerated wear of valve stem and valve body, such as destroy the sealing surface, lead to the oil. Repair if stem wear lighter, when to stem chrome plated finish; If the stem is worn badly, it needs to be replaced.

Q: People leave the forklift and do what and what to pay attention to when parking: To leave the forklift when the goods are not on the shelf, and to leave the forklift truck before leaving the forklift truck, and have to remove the goods or take down the cargo fork; 2, stop the brake handle to kill or press the brake switch; The engine is out of fire and the power goes out. Remove the key.

Q: Where should I take the special operation equipment certificate for the forklift?: The forklift card shall be the special operation certificate of the quality inspection bureau. You can go to the local quality supervision bureau special equipment department or the special equipment operator training school to take the exam training.

Q: Hydraulic forklift truck classification: Large capacity traction battery to ensure long working hours. Electric drive, electric lift; It is easy to operate and has broad vision. The frame is strong and the bearing capacity is strong. It runs in a balanced way. Large capacity traction battery to ensure long working hours. Type number: cbd-2.0 Maximum lifting weight: 2000Kg payload center distance: 600mm Minimum height: 85mm maximum height: 205mm Cargo fork length: 1150mm fork width: 530,680 mm Turn radius: 1525mm walking motor power: 1200W Improved power: 800W weight: 324

Send your message to us

*Email

*TEL

*Quantity

*Unit