HSS annular cutter(Practical version) DBHX(K)-2 D.O.C. 25mm
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 pc
- Supply Capability:
- 5000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
DBHX(K)-2
D.O.C. 25mm
Unit:mm
◎ Made of national-standard high speed steel with multi-cut geometry for ply-cutting to reach better removal of chips
◎ Applicable to hole cutting and process of annular groove on various magneric drills and press , like Alfra , Hougen , Jancy , Euroboor , BDS , Ruko
Annular Drill
1. Weldon shank, with more stable clamping for stable cutting and finish of holes.
2. Additional one hole on the shank of cutters ≤Φ40mm, fit arbors with 19.05 bore as well as quick-change system.
3. Applicable to hole cutting and process of annular groove on various magnetic drills and press, like Alfra, Hougen, Jancy, Euroboor, BDS, Ruko.
4. Made of high-performance high speed steel., e.g. M2, M2AL, M35, M42 etc. And can be used on various materials, like steel plate, Copper, aluminium, cast iron, stainless steel and plastic.
5. The specifications from the Φ12mm to Φ65mm, depth of cut from25mm, 35mm, 50mm, 75mm and 100mm.
Type | Size |
DBHK-20120 | 12*25 |
DBHK-20130 | 13*25 |
DBHK-20140 | 14*25 |
DBHK-20150 | 15*25 |
DBHK-20160 | 16*25 |
DBHK-20170 | 17*25 |
…… | …… |
DBHK-20550 | 55*25 |
DBHK-20560 | 56*25 |
DBHK-20570 | 57*25 |
DBHK-20580 | 58*25 |
DBHK-20590 | 59*25 |
DBHK-20600 | 60*25 |
- Q:How to allocate the electric hammer drill
- 1, backward extrusion head, drill can be pulled out.2, black down, iron also press down, it came out.
- Q:What kind of drilling bit is good for stainless steel?
- The characteristics of stainless steel is high toughness, easy to stick a knife. So the drill hardness is high, surface finish better than ordinary bits, the bit angle large (130--135 degrees). At the same time to the full amount of feed and cooling. More than 0.15mm as much as possible without cutting in cold hardened layer. The cutting speed is as low as possible to reduce the cutting temperature. The cutting fluid is made of concentrated emulsions. Commonly used stainless steel drills are: high cobalt bit (M35 bit, M42 bit), in which the M42 bit is the most cost-effective, and carbide drills are also available.
- Q:How do you get yellow on the surface of the drill bit?
- The Yellow above the drill is not baked. It is a kind of coating which is evaporated and ionized by the titanium metal in the high temperature and high vacuum environment. At the same time, the coating is added to the metal surface after the reaction of the reaction gas. It is also called PVD coating.
- Q:Relationship between bit diameter and rotation speed
- Secondly, it is related to the grinding, feed size, material and so on. Such as: stainless steel drilling, the drill speed and feed volume should not be too large, the need for flexible use.
- Q:At present, the strongest oil drill bit, the deepest can drill how many meters?
- Oil and gas drilling is divided by depth, 4500-6000 meters belong to deep well, 6000-9000 meters belong to ultra deep well, more than 9000 meters belong to special deep well.
- Q:What drill holes are used to break the screw?
- The metal, its principle is to discharge at the moment, a sharp change of arc temperature and with pressure, so that the metal material of the point immediately melted, gasification, splashed liquid and explosive, condensed into solid particles is the working fluid. At this time, the metal surface is etched into a pit, so EDM can be easily processed on any metal workpiece, so it is convenient and quick.
- Q:Electric hammer drill killed what should take down
- 1, backward extrusion head, drill can be pulled out.2, black down, iron also press down, it came out.3, there may be a problem that the pearl inside the chuck. The drill down, pressure head black chuck, a few more to return a bit range.
- Q:The maximum diameter of the hammer is fixed up? Can I open the hole? How does an electric drill screw in? How big is the drill bit?
- Put the drill will bite at the top of the hand claw loosen, the drill bit is put into a plug in the end, and tighten with the special wrench, if the old hammer, was struck with an iron wedge bite claw hammer with teeth to tighten the drill.
- Q:What is the difference between cobalt titanium alloy drill
- Alloy refers to two or more than two kinds of gold content are mixed together to form metal,
- Q:M3 threaded hole. The bottom should choose large diameter drill bit
- The bottom of the thread hole of the above M3 is the standard diameter of the drill bit made of ordinary materials. Of course, the actual production operation because the M3 screw mechanical properties of various materials is not the same as the processing of the material properties through appropriately adjusting, processing, such as M3 stainless steel threaded hole, must be to increase the diameter of the bottom hole processing, because the mechanical properties of stainless steel and ordinary materials are not the same. Stainless steel material hardness high, heat dissipation is poor, the reason of higher plastic, bottom diameter with a diameter of 2.7 bits. So in the actual operation, the operator should be through different material properties, adjust the threaded hole diameter of M3, so as to prepare for the next tapping.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
HSS annular cutter(Practical version) DBHX(K)-2 D.O.C. 25mm
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 pc
- Supply Capability:
- 5000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords