High Quality PPR single female threaded concealed stop valve

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

High Quality PPR single female threaded concealed stop valve Heavy stop valve size:20*1/2'',25*1/2''

1.Material:Random Polypropylene(Hyosung R200P);
2.ISO9001&ISO14001;
3.Standard:GB/T 18742.3-2002, DIN8077/8078;
4.OEM also ok

Q: Standard and specification for pressure test of valves: (11) when the valve with drive device is tested and its tightness is tested, the sealing test shall be carried out by using the driving device to close the valve. For manual drive units, seal test shall also be done with the actuating closing valve.(12) the by-pass valve installed on the main valve after the strength test and the sealing test. The strength and tightness test of the main valve is carried out. The main valve should be opened when the closing member is opened.(13) iron valve strength test, the application of Pratia tapping valve and valve cover, check whether there is any leakage.(14) the valve test, in addition to the provisions of the plug valve to allow sealing surface oiling, other valves are not allowed in the sealing surface of the oil test.(15) when the valve pressure test, the blind plate on the valve pressure should not be too large, so as to avoid deformation of the valve, affecting the test results (cast iron valve if pressed too tight, will be damaged).(16) after the valve test pressure, should promptly remove the water and clean the valve, should also be prepared for the test record.

Q: High and low pressure valve is how to distinguish?: Vacuum valve - valve with operating pressure below standard atmospheric pressure.Low pressure valve - nominal pressure PN is less than 1.6MPa valve.Medium pressure valve - nominal pressure PN 2.5~6.4MPa valve.High pressure valve - nominal pressure PN10.0~80.0MPa valve.Ultra high pressure valve - nominal pressure PN greater than 100MPa valve.

Q: What is the difference between the adjustable range of valve 50:1 and 100:1?: Adjustable ratio is also called adjustable range, if to R to indicate, then R=Qmax/Qmin should pay attention to the minimum flow, Qmin and leakage of different meanings. The minimum flow refers to the lower limit of adjustable value, it is generally the maximum flow rate of Qmax 2%~4%, and the leakage is fully closed when the leak valve, it is only the maximum flow rate of 0.1%~0.01%.Adjustable range 100:1 generally can not reach, the accuracy of this valve is very high.

Q: What does "1/2" mean on the valve?: 1/2 on the valve indicates that the ends of the valve are 1/2 inches in diameter.Valve is a control component in the fluid delivery system. It has the functions of closing, adjusting, guiding, preventing reverse flow, stabilizing voltage, shunting or overflow and releasing pressure.Valves used in fluid control systems, from the simplest stop valve to a very complex automatic control system used in a variety of valves, a wide range of varieties and specifications. Valves can be used to control air, water, steam, a variety of corrosive media, mud, oil, liquid metal and radioactive media and other types of fluid flow. The valve according to the material is divided into cast iron valves, cast steel valves, stainless steel valves (201, 304, 316), chrome molybdenum steel, chromium molybdenum vanadium steel valves, valve, dual phase steel valves, plastic valves, non-standard customized valve material etc..

Q: According to the original valve installed on it, but never demolished, I am afraid to force over, will not be broken? The old valve, that part of the remaining three tubes tight.: 1. Prepare the glue and saw blade. Disengaging bracket.2, using a hand saw from the valve mouth (spool near) transverse incision.3, the center will be on the move, the longitudinal incision, be careful not to damage the inner tube.4. Clean the pipe mouth, pipe and new valve coating, install the valve.Turn left and turn right |

Q: Which direction is the valve? Which direction is it?: Generally: clockwise, counterclockwise, looseYou can also see the logo on the spool

Q: What is the BV valve?: End code description link example (matching) BV PL endpoint endpoint oblique butt welding wire socket, socket welding (SWF) FL flange connection flange connecting pipe in the AutoCAD Plant 3D in connection with the pipe elements form in many ways, details are as follows: the end code description link example (matching) PL endpoint, outside the wire socket socketweld (SWF) BV oblique butt THDM external screw thread connection endpoint (THDF) THDF (THDM) SW screw thread connection wire socket welding socket welding flange connection flange connection FL WF flat flat flange link (FL) LAP (PL) GRV lap lap ring groove is connected with the connecting groove (PL) SO loose plate (PL) PPL plastic welding wire plane PSW plastic body adhesive (PPL) LFL LLP LUG straight straight flange lap lug flange (FL) BEL L bell shaped joint, bell and socket welding (SPIG), SPIG socket welding, bell shaped joint and socket welding (BELL) TAP plug cock (PL)

Q: What do the D373W and D373H of the valve mean?: Butterfly valve, worm drive for the folder inclined plate, H alloy steel lining, W for the valve body directly processing sealing surface.

Q: Why can't the clip type check valve be directly connected with the pipe mouth or other valves?: The clip type check valve is made up of two discs to prevent backflow.If the clip check valve is connected to the other valve, the disc may touch the valve and cause the check valve not to be fully opened or closed. This is a preliminary analysis of "enter the valve", for reference only!

Q: How does the valve close?: This is a relatively vague ah, like the stem ah, usable spanner clamping, clockwise rotation in the end. The handle should be closed groove and the coincidence place.

Send your message to us

*Email

*TEL

*Quantity

*Unit