High Quality PP-R stop valve with elbow

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

High Quality PP-R stop valve with elbow Heavy stop valve size:20*1/2'',25*3/4''

1.Material:Random Polypropylene(Hyosung R200P);
2.ISO9001&ISO14001;
3.Standard:GB/T 18742.3-2002, DIN8077/8078;
4.OEM also ok

Q: Standard and specification for pressure test of valves: (11) when the valve with drive device is tested and its tightness is tested, the sealing test shall be carried out by using the driving device to close the valve. For manual drive units, seal test shall also be done with the actuating closing valve.(12) the by-pass valve installed on the main valve after the strength test and the sealing test. The strength and tightness test of the main valve is carried out. The main valve should be opened when the closing member is opened.(13) iron valve strength test, the application of Pratia tapping valve and valve cover, check whether there is any leakage.(14) the valve test, in addition to the provisions of the plug valve to allow sealing surface oiling, other valves are not allowed in the sealing surface of the oil test.(15) when the valve pressure test, the blind plate on the valve pressure should not be too large, so as to avoid deformation of the valve, affecting the test results (cast iron valve if pressed too tight, will be damaged).(16) after the valve test pressure, should promptly remove the water and clean the valve, should also be prepared for the test record.

Q: What is the normal temperature on the valve?: At normal temperatures are below 120 degrees. A lot of valve sealing surface can only reach 120 degrees

Q: For example, the knife gate valve, PZ73X-10C, DN50 torque is 5, torque is what role? What units?: Unit: Newton M. torque is the minimum torque used to turn on the valve. It is the force that opens the valve!The valve that indicates the opening of the PZ73X-10C DN50 requires 5 meters of force.

Q: Can other valves be used instead of 10?: An elbow, an outer wire, screw down the joint of the hose, the elbow is joined together.

Q: A kitchen, 2 bathrooms, in addition to the toilet, toilet (only cold water), the rest need hot and cold water supply, and hot water by solar water heaters and gas water heater selection. The kitchen is mainly a sink, each toilet for toilet, shower, washbasin, separate cold water faucet. I don't know how many metal materials I'll use now Thank youThe waterways are all dark!: Landlord water and electricity installation? If you ask the water electrician to install it, you don't need to worry about it so much. You can wait for water electrician to install the hot and cold water pipe in place. We can count on you here.

Q: such as gate valve, three way plug valve: The lower part of the pressure gauge installed water pipe, there are water, avoid high temperature, medium pressure gauge contact directly cause damage, so regular cleaning, in order to avoid congestion, three way plug function is used for flushing, please see "how to operate them.".

Q: The total valve of my natural gas was closed by the attitude I tried. Now I can't open it. I need to use gas. Who knows how to drive it? What skills do I have? I'm talking about the main valve.: Are you talking about using air? Or your valve is a pneumatic emergency shut-off valve

Q: Automatic exhaust valve installed in the pipe before and after the installation of other valves need to press it?: In general, the exhaust valve (large diameter) and a maintenance valve, normally open,

Q: What is the diameter of a general pipe valve?: In fact, the essence of the problem is the corresponding relationship between the nominal diameter and other dimensioning methods. Valves are generally marked with nominal diameter (DN***), such as DN150, DN100 and so on. There are many kinds of marking methods for pipes, such as outer diameter, inch inch, nominal diameter, etc.. Only when the other dimensioning is converted to nominal diameter, the valve and the pipe correspond to each other.