H.F pipe line / φ50 pipe line roll forming machinery
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 100 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Structure of φ50 pipe line Description
Product introduction：General Description. Material to be processed:Carbon Steel, Cold Hot Rolled pre slit strip coils of weld able grade with max. 0.2% carbon.
Main Features of the φ50 pipe line
Type of Production: * Round Tubes*Squar *Square and Rectangular Hollow Sections
Round Tube Outside Diameter: Min 15 Max 63mm
Square Hollow Section: Min 10 x10 Max 50 x 50 mm
Rectangular Hollow Section: Min 10 x 15 Max 40x 60 mm
Tube Thickness: Min 0.5 Max 3.25 mm
Forming Line Speed: Max 100 m/min (Square and Rectangular Hollow Shapes are produced at lower speeds depending on side to wall thickness ratio)
Tube Cut Length: Min 4 Max 12 meter
Length Accuracy: ± 3mm
Main Drive Motor: DC 55kW×2
The φ50 pipe line Specification
Line Composion
Double Mandrel Uncoiler
Shear and TIG Welder
Horizontal Strip Accumulator.
Forming, Welding, Cooling and Sizing Section.
Computer Flying Saw Cut-Off.
Driven Roller Run Out Table, Inspection table Collectors.
Solid State H.F. Induction Welder: 150 kW, Solid State(or 200kW,Vaccum Tube Type).
Rolls: Rolls are manufactured out of AISI D3 D2 or E52100
Electrical Panels
φ50 pipe line Imange
FAQ
How do you guarantee the quality?
We can provided CE certificate if we are required.
What's the delivery time?
around 120days after receive your 30% payment.
Where can we see your machines?
You are welcome to visit our factory and test it by yourself.
- Q: A roll forming machine, rolling out of the length is always not up to a fixed size, not too small, that is, more than that, what is the cause?
- According to my experience, there should be a problem with the boot encoder (also known as the digital wheel). Thank you. I hope I can help you.
- Q: What is rolling forming processing?
- A special rolling tool is used to exert certain pressure on the surface of the workpiece so as to make the surface metal flow.
- Q: Improvement in rolling forming process
- It is difficult to control the rolling process and can cause waste easily.
- Q: Introduction of roll forming process
- Roll forming began around 1960s in europe. Because of roll forming, the working model has the advantages of high production efficiency, saving material and increasing product strength.
- Q: What kind of material and what heat treatment are used for pressing roller (molding, feeding, cutting force, heavy load, heavy load) of sheet steel rolling machine?
- Non bonding wear of rolled material (especially stainless steel strip, etc.)
- Q: What is the surface rolling forming machine process?
- The rolling process using metal at room temperature, cold plastic characteristic, through the rolling tool is the rolling tool to put some pressure on the metal surface, so that the workpiece surface by plastic deformation, the height to the lower tissue slip, the surface roughness decreased.
- Q: Process mould for rolling forming process
- A movable wire plate, made of the same fixed wire plate, for relative reciprocating motion. Roll forming is the design of different structures on the plate rolling on the workpiece. Roll out all kinds of thread, convex ring, knurling, end chamfering, groove with different width and thickness as well as other required shapes.
- Q: Material and equipment for roll forming process
- The most common type of roll forming is reciprocating flat wire twisting machine. Therefore, for the manufacturers of cold heading machines and screw rolling mills, the design of rolling dies is only a matter of design.
Send your message to us
H.F pipe line / φ50 pipe line roll forming machinery
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 100 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
