FERRULE DN8
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
| PART NO. | HOSE BORE | DIMENSIONS | ||
| DN | DASH | D | L | |
| 03310-04 | 6 | 4 | 23 | 30.5 |
| 03310-05 | 8 | 5 | 24 | 30 |
| 03310-06 | 10 | 6 | 26 | 32 |
| 03310-08 | 12 | 8 | 29 | 34 |
| 03310-10 | 16 | 10 | 33 | 37 |
| 03310-12 | 20 | 12 | 37 | 42 |
| 03310-16 | 25 | 16 | 46 | 51 |
| 03310-20 | 32 | 20 | 59 | 59 |
| 03310-24 | 38 | 24 | 67 | 67 |
| 03310-32 | 51 | 32 | 80 | 72 |
1) FERRULE
FERRULE for SAE100R1AT/EN 853 1SN HOSE
FERRULE for SAE100R1A EN 853 1ST HOSE
FERRULE for SAE100R2AT/DIN20022 2SN HOSE
FERRULE for SAE100R2A/EN8532SN HOSE
FERRULE for SAE100R1AT-R2AT,EN853 1SN-2SN and EN 857 2SC
FERRULE for 4SP, 4SH/10-16, R12/06-16 HOSE
FERRULE for 4SH, R12/32 HOSE
2) SWAGED METRIC FITTINGS
Metric Flat Seal Fittings Metric Multiseal Fittings
Metric 60°Cone Seal Fittings Metric 74°Cone Seal Fittings
Metric 24°Cone O-RING Seal L..T. Fittings Metric 24°Cone O-RING Seal H.T. Fittings
Metric Standpipe Straight Fittings JIS Metric 60°Cone Seal Fittings
3) SWAGED BRITISH FITTINGS
BSP O-RING Seal Fittings BSP Flat Seal Fittings
BSP Multiseal Fittings BSP 60°Cone Seal Fittings
BSPT Fittings JIS BSP 60°Cone Seal Fittings
4) SWAGED AMERICAN FITTINGS
SAE O-RING Seal Fittings ORFS Flat Seal Fittings
NPSM 60°Cone Seal Fittings JIC 74°Cone Seal Fittings
NPT Fittings SAE Flange L.T. Fittings SAE Flange H.T.Fittings
5) STAPLELOK FITTINGS
BANJODOUBLE CONNECTION INTERLOCK HOSE FITTINGS
6) METRIC ADAPTERS
Metric Thread O-RING Face Seal Adapters
Metric Thread Bite Type Tube Adapters
Metric Thread 74°Cone Flared Tube Adapters
JIS Metric Thread 60°Cone Adapters
7) BRITISH ADAPTERS
BSP Thread 60°Cone Adapters
JIS BSP Thread 60°Cone Adapters
BSPT Thread Adapters
8) AMERICAN ADAPTERS
ORFS ADAPTERS JIC 74°Cone Flared Tube Adapters
NPT Thread Adapters
- Q: What is the difference between the precast beam of the bridge and the method of pulling out the rubber tube after pouring the concrete? What's the difference between design and calculation?
- Corrugated pipe is included in the design of the amount of engineering, the role is: reserved strand space. Its length is calculated when the work length of the steel strand.
- Q: Access toilet water inlet hose joints, how to repair water?
- However, be careful not to hold back too much to prevent the toilet from being cracked. Because before if overwind, or rust, is not open, can only remove the drainage valve inside with a pipe wrench stuck open.
- Q: How to make a rubber tube requires flow
- High pressure rubber hose made of inner rubber, steel wire (braid layer), outer rubber. High temperature processing and vulcanization.
- Q: Hydraulic hose joint dimensions
- Metric plain thread1. metric screw thread with a capital M, tooth type angle 2 degrees =60 (alpha tooth type half angle);2. metric ordinary thread by pitch, coarse teeth, ordinary thread and fine teeth, two kinds of ordinary thread;2.1. coarse tooth ordinary thread mark generally does not indicate the pitch, such as M20 means coarse thread; fine tooth thread mark must indicate the pitch, such as M30 * 1.5 for fine tooth thread, in which pitch is 1.5.2.2. common thread is used for the connection and fastening between the mechanical parts, and the general thread connection is mainly made of coarse thread. The thread strength of the fine tooth thread is slightly higher than that of the same nominal diameter, and the self-locking performance is better.Mark 3. metric screw thread: M20-6H, M20 * 1.5LH-6g-40, where M represents a common thread metric, 20 nominal diameter thread is 20mm, 1.5 pitch, LH said, 6G 6H left, said thread precision grade, precision grade of internal thread uppercase, lowercase precision grade of said external thread, 40 screwing length.
- Q: Latex tube, rubber tube, silicone tube, which three of the best tightness?
- Rubber tightest is butyl rubber, rubber pipe products in general, with no fiber layer, expanding 300-500% is no problem, you can put it into the glass tube, depends on the strength of the glass tube and technique.
- Q: What are the matters that should be paid attention to when installing rubber hose joint in water pump?
- Installation notes:?1, Shanghai rubber pipe joint non super displacement limit at the time of installation;?, 2 installation bolts to be symmetric, gradually tightening pressure, to prevent local leakage;?3, flat, suspended, vertical installation of rubber pipe joint, actual axial displacement pressure rubber tube joints should be smaller than the pipe support, otherwise should install anti pull off device to prevent work pressure;?4, rubber pipe joints should be away from heat, ozone, no strong radiation light. Exposure and use of media that do not meet the requirements of the product;?5, rubber pipe joint in the transportation, loading and unloading, installation, no sharp instruments across the surface of the sealing surface;
- Q: How to determine the tensile strength of GB rubber joint?
- The cutting of sample can be done by punching machine. When punching sample, the following points should be paid attention to.The cutting force is uniform, not too large, and with mild soap and water and clean tap water wet specimens (or tools), if a sample cut down, it should be abandoned, not to repeat the old mark for cutting.The direction of specimen cutting should be consistent with the direction of tension and the direction of rolling.
- Q: What are the categories of hose?
- A rubber hose products structure: hose cloth; woven hose (fiber braided hose, steel wire braided hose); winding hose (fiber winding hose, hose winding wire); knitted hose, hose and other circular weaving hose (rubber hose, rubber and plastic composite hose and hose, drilling hose, etc.).
- Q: Why are the lengths of the household combustion equipment linked to the gas pipe hose no more than 2 meters?
- A pipe is a weak link. Many accidents occur on pipes. In theory, the leakage of pipe per unit length may be the same. Then, the longer the pipe, the higher the risk coefficient.In reality, the longer the tube, the higher the possibility of being clipped. For example, bending, stretching, foot work, cracking, aging, these are potentially dangerous.
- Q: The difference between the rubber pipe and PE pipe?
- The appearance of the native HDPE is milky white and is somewhat translucent in the narrow cross section. PE has excellent properties that are resistant to most life and industrial chemicals. PE pipe welding, butt welding of PE pipeline, the method provides the highest reliability and the diameter of the range and pressure process: the end of the heating tube, using a tool called mirror contact pressure and temperature under the definition of "". The ends are contacted rapidly and remain under pressure during cooling. A medium density polyethylene pipe and PE pipe with high density polyethylene pipe. Divided into SDR11 and SDR17.6 series according to the wall thickness. The former is suitable for transporting gaseous artificial gas, natural gas and liquefied petroleum gas. The latter is mainly used to transport natural gas.
Send your message to us
FERRULE DN8
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
