Ductile Iron Butterfly Valve On Top Sale
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 set
- Supply Capability:
- 1000 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Manual Wafer Butterfly Valve Description:
A butterfly valve is a valve which can be used for isolating or regulating flow. The closing mechanism takes the form of a disk. Operation is similar to that of a ball valve, which allows for quick shut off. Butterfly valves are generally favored because they are lower in cost to other valve designs as well as being lighter in weight, meaning less support is required. The disc is positioned in the center of the pipe, passing through the disc is a rod connected to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.
2.Main Features of the Manual Wafer Butterfly Valve
a)Cast hole. Flange connection meet ANSI 125/150# DIN PN10/16 BS4504 PN10/16 in the meanwhile.
b)Soft seat. Replaceable. Increase of service life.
c)Double half shaft without pin.
d) Square and short neck. Easy to stick scutcheon and cost saving.
3. Manual Wafer Butterfly Valve Images:
4.Manual Wafer Butterfly Valve Specification:
1)Size: DN40-DN1400
2)Material:body-CI/DI/WCB/SS
disc:DI/CF8/CF8M/C95400
3)Professional Maufacturer for more than 10 years
PRESENTATION:
1) Sizes:
DN40mm-DN1400mm
2) Materials:
a) Body: CI(cast iron ,GG25 )/ DI (ductile iron ,GGG40)
b) Disc: DI / CF8 / CF8M / C95400
c) Seat: EPDM / NBR / TEFLON / VITON
5.FAQ
1. What is manual wafer butterfly valve?
A: Wafer style is the more common of the two and is less expensive than the lug style. The wafer style butterfly valve is just about the standard. It ís so common that no one even bothers to use the word "wafer" when ordering a butterfly valve. It is taken for granted that if a butterfly valve is ordered, a wafer style will be received.
2. How about the Installation of the Wafer Style Butterfly Valve?
A: Butterfly valves are installed by inserting the valve between two flanges using bolts or studs and nuts to hold it all together. This type of installation, of course, makes it impossible to disconnect just one side of the piping system from the valve. That benefit is received using the lug style valve.
3. What is the working principle of manual wafer butterfly valve?
A: A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "butterfly" is a metal disc mounted on a rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway. When the valve is fully open, the disc is rotated a quarter turn so that it allows an almost unrestricted passage of the fluid. The valve may also be opened incrementally to throttle flow.
- Q:Remove the handle and lever the stem rotation with a wrench,
- First you know what valve you need, or you know where to use the pipe material, so you do not need to understand the valve material.
- Q:How does the valve open?
- Now the valve is in a closed state, the general valve on the valve flow direction marked, like you figure on this, flat side perpendicular to the flow channel is closed, parallel to the flow channel is open.
- Q:What are the uses and differences of gate valves, butterfly valves, ball valves and other valves?
- Valve and ball valve is generally used in the main pipe, long-term use, butterfly valve is often used frequently,
- Q:The total valve of my natural gas was closed by the attitude I tried. Now I can't open it. I need to use gas. Who knows how to drive it? What skills do I have? I'm talking about the main valve.
- General domestic weather is more ball valve, counterclockwise turn 90 degrees can.
- Q:How to better maintain the valve?
- How to maintain the valve?Enter the same as other mechanical products, but also the need for maintenance. This work well, can extend the service life of the valve, the following will introduce the valve maintenanceStorage and maintenanceThe maintenance of the purpose is to keep the valve in the custody of the damage, or lower quality. In fact, improper storage is one of the important reasons for valve damageThe valve custody, should be arranged in good order, a small valve on the shelves, large valves can be neatly arranged in the warehouse on the ground, not arbitrary lumber pile, do not let the flange face contact with the ground. This is not only for beauty, mainly to protect the valve, not to touch badBecause the storage and handling properly, hand wheel broken, crooked stem touch the fixed nut hand wheel and stem loosening loss and so on, these should avoid unnecessary losses.We temporarily on the short-term use of the valve, should remove the asbestos packing, in order to avoid electrochemical corrosion damage to the valve stem.I just entered the library on the valve, to conduct inspections, such as during transport into the water or dirt to wipe clean, re storedThe import and export of valves to use wax paper or plastic sheet sealed to prevent dirt insideThe valves on the machined surface rust in the atmosphere should be coated with anti rust oil, protectI placed outside the valve, must be covered with linoleum or tarpaulins like rain, dust items. Keep the storage of the valve clean and dry
- Q:Valve category can fill the trunk door, branch valve Mody?
- Each of these types of valves have very different varieties, such as the valve can be divided into: self sealing valve, knife gate valve, gate valve, cryogenic insulation jacket valve, seal valve, vacuum valve, flexible valve seat seal, valve, gate valve, signal buried forged steel gate, cast iron gate valve and so on.
- Q:Proportional valve why than other small pipeline valves
- 3.8 valveGraphical representation of numbers, names, symbols3.8.1 angle valve at room temperature3.8.2 cold angle valve for low temperature use3.8.3 stop valve at room temperature3.8.4 ball valve often 9 temperature3.8.5 valve at room temperature3.8.6 butterfly valve at room temperature3.8.7 check valve flow from blank triangle to non empty triangle3.8.8 pressure reducing valve, small triangle for high voltage end3.8.9 throttling valve is needle valve3.8.10 three-way valve for normal temperature use3.8.11 four way valve used at normal temperature3.8.12 safety valve spring type safety valve3.8.13 trap actual drawing, you do not have to draw arrows3.8.14 inflator, cold box, little gas huff and puff, safe useValve for normal temperature of regeneration valve of 3.8.15 reverse stop valve3.8.16 reverse loading cold angle valve
- Q:What is the diameter of a general pipe valve?
- The relation between the common mark and the nominal diameter:1, plastic pipes (U-PVC, water pipes, PPR tubes): Phi 20-DNl5, Phi 25-DN20, Phi 32-DN25, Phi 40-DN32, Phi 50-DN40, Phi 63-DN50, Phi 75-DN65, Phi 90-DN80, Phi 11O-DNl00, Phi 160-DNl1502, seamless pipe: DN15- 22mm DN20- 27mm DN25- phi, Phi Phi Phi Phi 34mm, DN32- 42mm DN40- 48mm DN50- 60mm DN65-, Phi Phi 76 (73) mm, DN80- 89mm DN100- 108mm DN125- phi, Phi Phi 133mm, Phi 159mm, Phi DN150- DN200- 219mm, DN250- 273mm3, DN15---1/2--- four; DN 20---3/4--- six; DN 25---1, DN 32--1 1/4 -- an inch; inch two; DN 40---1 1/2 DN 50--- - an inch and a half; 2 - two inch DN 65---; 2 1/2, two and a half inches; DN 80--- 3 - three inch two; DN 100--- 4 - four inches; DN 125-- 5 - DN 150--- 6 - five inch; six inch 8---- eight inch 200--- DN;
- Q:How much is the 150LB of the valve?
- 150Lb=2.0MPa=20 kg.Valve (Famen) is a control component in the fluid delivery system. It has the functions of closing, adjusting, guiding, preventing reverse flow, stabilizing voltage, shunting or overflow and releasing pressure.Valves used in fluid control systems, from the simplest stop valve to a very complex automatic control system used in a variety of valves, a wide range of varieties and specifications.
- Q:I would like to ask how the valve entry, for a new pair, really difficult, what cutaway view, there are other, just contact the valve less than a week, and sometimes it is really difficult to understand. Forget the experienced teacher can be generous with your criticism to later, indebted forever, learn the valve Comrades some help.In a company CAD to relatives as soon as possible to a company, and then slowly improve, I do not know what is the request of the novice, and how to start as soon as possible, I am learning routine is: give me a set of valve design drawings, and then I paint it on, do not understand the structure and workshop look. I wonder if you have any good learning methods that can be referred to and supplemented by younger brother
- I was about 08 years of contact valve, indeed many, but a company, all products will not have, are designed to do certain types of valves, such as for HVAC, or petrochemical, some other valves used in engineering, will do the purchase, so you only according to the company's products study on the line, need to learn what, what, high efficiency.If you do the design, you have to learn a lot of things: "mechanical design manual" and "valve design manual" is essential, often used;Of course, functional things are the basis, that is, the structure, the work principle must be obtained first, in order to do relevant design and improvement;First of all, the structure design, CAD must learn, three-dimensional software also have to learn one, Solidworks, Peo/E, UG, Catia can be;Second, strength analysis is necessary, so in mathematics, mechanics, mechanical design things to learn solid; can make strength analysis with finite element analysis software, need to learn, software Comosworks, Ansys;Third, the valve design will have fluid aspects, flow design, flow capacity, flow characteristics of the study, to study fluid mechanics, heat transfer, etc., CFD software has Fluent, Ansys, CFX, Star-CD;In addition, materials and technical aspects should be learned.Slowly, I also step by step by side with coming.Hope to be of help to you.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Ductile Iron Butterfly Valve On Top Sale
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 50 set
- Supply Capability:
- 1000 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords