Dlc Listed Led Tube T5 T8 T10 2Ft 3Ft 4Ft 5Ft 8Ft(600Mm/900Mm/1200Mm/1500Mm/2400Mm)
- Ref Price:
-
$0.11 - 49.90
/ pc
- Loading Port:
- Shenzhen
- Payment Terms:
- L/C,T/T
- Min Order Qty:
- 10 Pieces pc
- Supply Capability:
- 50000 Pieces pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Led t8 tube ul
1)New patent new design
2)American Canada Market
3)60cm 90cm 120cm 150cm
4)SAA TUV ETL UL CE
Specifications:
Power | 18W |
Input Voltage | AC85V~265V |
Luminous Flux (lm) | 2050-2200lm |
Socket | G13/R17D |
Size | 26*1200mm(T8) |
LED Quantity | 96pcs (SMD2835) |
Tube Material | Aluminum+Clear/Striped/Frosted PC cover |
Beam angle | 120degree |
CCT | 2800-7000K |
Features and Specifications:
| 1, Energy saving:ultra low power,and saves more than 60% energy than traditional incandescent lamp. |
| 2, Environmental protection:no radiation, no mercury or lead, completely recyclable. |
| 3, Super long life span:50,000 hours, life is 10 times longer than traditional lamp. |
| 4, High quality illuminant:using highlight SMD3014 illuminant, each lamp bead attains 7-8LM. |
| 5, Drives:isolation constant-current supply driver with high efficiency and high-low pressure to enhance product performance entirely. |
| 6, Autonomous mold opening to make aluminum alloy extrusion shell ,simple and beautiful looking,scientific and reasonable heat dissipation structure. Scientific light distribution ,uniform illumination.safety in use and easy installation. |
Choosing Avaliable:
| No. | Power | Length | QTY led | Lumen | Voltage | CCT | SMD |
| FLD-T8-60-10W-S | 10W | 600 | 48 | 1100-1200lm | 85-265V | 2500-6500K | 4014 |
| FLD-T8-90-12W-S | 12W | 900 | 72 | 1332-1500LM | 85-265V | 2500-6500K | 4014 |
| FLD-T8-120-18w-S | 18W | 1200 | 96 | 2000-2200LM | 85-265V | 2500-6500K | 4014 |
| FLD-T8-120-22W-S | 22W | 1200 | 105 | 2442-2750LM | 85-265V | 2500-6500K | 4014 |
| FLD-T8-150-25W-S | 25W | 1500 | 126 | 2775-3125LM | 85-265V | 2500-6500K | 4014 |
Installation
1. cut off the power supplybefore installation;
2. No starter, NO ballast, or electronic switch is required;
3. Install lamp stand and T8 lamp holder first with the same length;
4. Lamp working voltage is AC85-265V.
5. Connect the two wire terminals located at the side of the lamp to the electricity L and N respectively;
6. Do not supply the power to both pins on the same end simultaneously
Please reference Installation of 2D Draw:
Product Features
|
Note:
1.LED tube light input Voltage: AC85-265V
2.Color Rendering Index(CRI): 80±5%RA
3.Beam Angle: 120°
4.Working temperature: -30°C~50°C
5.Ambient Humidity: 10%~90%
6.Lifespan: 50,000hours
7.Shell material: Aluminum + PC(Transparent/Mist)
8.IP Rating: IP50
9.Shell Color: Silver
Trade Term
1.delivery term:FOB,EXW,CIF are available.
2.payment term:30%T/T advance,70% balance before shipment,Western Union or paypal is acceptable for samples orders.
3.lead time:3-7 days for samples, 7-20 working days for the large quantity.
Application
1. living room, bedroom, kitchen, washroom
2. School, University, Hospital, Hote
3. Conference, Meeting room, Show room, Showcase
4. Commercial Complexes
5. Factories, Plants, Warehouses, Offices
6. Super-market, Department store
- Q: A 30-watt light bulb can be used for a change of LED lamp
- The fluorescent lamp bracket some trouble, generally in the power of the led lamp is generally in 18 w 9 w, 600, 36 w in 18 w, 1200 long, 30 w words should be in 12 or 15 w, do you want to make sure the tube length.
- Q: The two ballast that originally was electric inductance towed three ordinary fluorescent lamps, now changed to LED fluorescent lamp tube, have influence?
- You slam the door of the original circuit, LED fluorescent tube is in with the drive, as long as according to the directions, the wire connected, the zero line of the original circuit is a traditional fluorescent lamp ballasts, and LED is not the same, so you can cut down, the original circuit directly connected to your leds.
- Q: Can the LED tube be installed as a general lamp holder? It won't burn easily
- Cannot be installed directly, need to change internal wiring. Leds are not the same as the traditional lamp tubes, which have the power supply inside the LED tube, and the input voltage at both ends of the tube is 220V. The traditional lamp power source is placed outside, and the voltage at both ends of the lamp is as high as a few hundred volts. If the LED tube is directly installed, it will burn down the power in the LED lamp tube because of the hundreds of volts of voltage that the original fluorescent lamp's ballast outputs. 3, therefore, the LED light tube cannot be installed directly in the traditional fluorescent tubes, the need to remove the internal ballast, then change the input at the ends of the line. LED bulbs are usually two incoming lines, one firewire and one zero line.
- Q: What is the minimum starting voltage for the fluorescent tube?
- The fluorescent lamp is under the influence of the ballast, the voltage is 810 volts. 810 volts is transient and can only be observed with a digital oscilloscope. I measured the data in three different meters, and the data doesn't really have the same data.
- Q: How do you know whether a fluorescent tube is good or bad
- How do you know whether a fluorescent tube is good or bad
- Q: Why does the led fluorescent tube have water vapour in it? What causes it?
- The starter down. When the regenerator was knocked down, my home was my own scissors and cut off the ends of the two ends of the regenerator. Then attach the severed head to the insulation tape. search Put the base back to the original. The head of the LED fluorescent tube will be plugged into the base current
- Q: What are the details of the whole process of the LED lamp?
- LED lamp tube application CE certification, notice two aspects 1, sample selection, had better be to isolated power supply, power supply aspects need separate power supply L/N line at one end of the input, and weight requirements, should not exceed 500 g is 1.5 meters. It is difficult to meet the weight requirement by more than 1.5 meters. For other details, look at specific products and specific analysis. There are specific tests, detailed analysis... 2, the detection organization's choice. There are international authorities such as TUV, ITS, etc. Customers have these special requirements. According to customer's requirement. It is best to choose domestic CNAS. , Note: in March 2013, LED lighting was added to EN 62493: test standards for 2010, enforcement.
- Q: Now there is no led lighting, just like the fluorescent light bulb, which is universal
- Yes, on some treasure, I have just changed a batch of such tubes, no more than 8 yuan or so.
- Q: Can the T5 light tube be free of ballast?
- Your home is long and thin lamp tube connect seat, that is electronic town flow, the element is installed on which small base, some pack on both sides, cannot not have no!
- Q: ?The title What is the color temperature of the leds?
- There are two types of traditional daylight lighting, the warm color of 3000K and the positive white 6500K, and the leds are almost as close as the two colors.
Send your message to us
Dlc Listed Led Tube T5 T8 T10 2Ft 3Ft 4Ft 5Ft 8Ft(600Mm/900Mm/1200Mm/1500Mm/2400Mm)
- Ref Price:
-
$0.11 - 49.90
/ pc
- Loading Port:
- Shenzhen
- Payment Terms:
- L/C,T/T
- Min Order Qty:
- 10 Pieces pc
- Supply Capability:
- 50000 Pieces pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
