Butterfly Valve on Sale with Worm Gear Actuated Flange Triple Eccentric
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 1000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Manual Wafer Butterfly Valve Description：
A butterfly valve is a valve which can be used for isolating or regulating flow. The closing mechanism takes the form of a disk. Operation is similar to that of a ball valve, which allows for quick shut off. Butterfly valves are generally favored because they are lower in cost to other valve designs as well as being lighter in weight, meaning less support is required. The disc is positioned in the center of the pipe, passing through the disc is a rod connected to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.
2.Main Features of the Manual Wafer Butterfly Valve
a)Cast hole. Flange connection meet ANSI 125/150# DIN PN10/16 BS4504 PN10/16 in the meanwhile.
b)Soft seat. Replaceable. Increase of service life.
c)Double half shaft without pin.
d) Square and short neck. Easy to stick scutcheon and cost saving.
3. Manual Wafer Butterfly Valve Images：
4.Manual Wafer Butterfly Valve Specification：1) Sizes:
DN40mm-DN1400mm
2) Materials:
a) Body: CI(cast iron ,GG25 )/ DI (ductile iron ,GGG40)
b) Disc: DI / CF8 / CF8M / C95400
c) Seat: EPDM / NBR / TEFLON / VITON
5.FAQ
1. What is manual wafer butterfly valve?
A: Wafer style is the more common of the two and is less expensive than the lug style. The wafer style butterfly valve is just about the standard. It ís so common that no one even bothers to use the word "wafer" when ordering a butterfly valve. It is taken for granted that if a butterfly valve is ordered, a wafer style will be received.
2. How about the Installation of the Wafer Style Butterfly Valve?
A: Butterfly valves are installed by inserting the valve between two flanges using bolts or studs and nuts to hold it all together. This type of installation, of course, makes it impossible to disconnect just one side of the piping system from the valve. That benefit is received using the lug style valve.
3. What is the working principle of manual wafer butterfly valve?
A: A butterfly valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "butterfly" is a metal disc mounted on a rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway. When the valve is fully open, the disc is rotated a quarter turn so that it allows an almost unrestricted passage of the fluid. The valve may also be opened incrementally to throttle flow.
- Q: How do i use a valve spring compressor. It looks like a c-clamp, so don't tell me how to use a smaller one, but the bigger one.Thanks
- the forked end of it will go over the spring part and the solid will work on the valve ,you can only use this one if the head is off though,the smaller ones work good if the head is still on the car,the c-clamps style though is the best one to use its safer and wont allow the springs to fly off,good luck.
- Q: What is the medium flow rate when the centerline butterfly valve is fully open?
- After inspection, the product certificate shall be attached to the factory.Butterfly: also known as butterfly valve, control valve has a simple structure, can be used for low pressure pipeline valve switching control is closed parts (disc or disc) is a disk, around the valve axis to achieve the opening and closing a valve, the valve can be used to control air, water, steam, all kinds of corrosive media, mud, oil, metals and radioactive liquid media and other types of fluid flow.
- Q: What does the butterfly valve D361H - 25C DN350 mean?
- Welded turbine butterfly valve, hard seal, material: cast steel, pressure 25KG, caliber 350MM
- Q: What are the major disadvantages of butterfly valves?
- Rubber elastomer in the butterfly valve will cause tear, wear, aging, perforation and even shedding in continuous use. The traditional heat curing process is difficult to adapt to the needs of on-site repair. It is time-consuming and laborious to use special equipment when repairing, and it consumes a lot of heat and electricity. Nowadays, polymer composite method is gradually used instead of traditional method.
- Q: What does butterfly valve do?
- 5, connections are flanged, wafer connections, welded connections and lugs on the clip connection. ?Drive in the form of manual, worm gear, electric, pneumatic, hydraulic, electro-hydraulic linkage actuator, can realize remote control and automation.Advantages of butterfly valves1, opening and closing convenient, fast and labor-saving, fluid resistance is small, you can often operate. ?2, simple structure, small volume, light weight. ?3, to transport slurry, accumulation of fluid in the pipe outlet at least. ?4, under low pressure, can achieve a good seal. ?5, good regulating performance.Disadvantages of butterfly valve1, use pressure and working temperature range is small. ?2, poor sealing. ?Butterfly structure can be divided according to the bias plate, vertical plate, inclined plate and lever type. According to the form of sealing can be divided into soft sealing type and hard sealing type of two. The soft sealing type usually adopts rubber ring seal, and the hard sealing type usually adopts metal ring seal. ?By connection type can be divided into flange and clamp connections; press can be divided into manual transmission, gear transmission, pneumatic, hydraulic and electric types.
- Q: How do hydraulic butterfly valves work?
- 3. butterfly valve hydraulic drive device structureThe valve hydraulic device is mounted on the valve drive shaft. The driving shaft of the valve is fixed with a transmission spline, and the crank (with an outer spline) is sleeved on the driving shaft. When the hydraulic system works normally, through the gear sleeve, the transmission spline is connected with the crank. Thus, the hydraulic cylinder drives the crank, and the spline on the crank passes the torque to the transmission spline by means of a gear sleeve. Because the driving spline is fixed on the driving shaft, the driving shaft rotates and drives the valve plate to start and close. A section of optical axis is arranged at the end of the driving shaft and is inserted into the end of the manual shaft (matched with the clearance of H11/ H11), and the function is that the manual shaft is concentric with the main drive shaft. In normal operation, the optical axis rotates with the drive shaft, but the manual device does not move. When the hydraulic operation is performed manually or manually from the hydraulic unit, a * * * conversion is required. The utility model is composed of a nut, a hand wheel, a screw rod, a support frame and a shifting device. When the utility model is switched, the hand wheel is rotated and driven by the screw rod to move. A guide rod is arranged on the bracket to make the shift and translation stable.
- Q: Which is more expensive, gate valve or butterfly valve?
- Gate valves of the same material and specifications are much more expensive. The weight of the gate valve is much heavier than that of the butterfly valve.
- Q: D341W-10P-400 butterfly valve, what does each alphanumeric letter mean?
- According to JB/T308-2004 "valve type programming method"D butterfly valve3 worm gear4 flange connection1 Structure: sealed type, central vertical plateW sealing material for valve body material10 nominal pressure PN10P body material is chromium nickel stainless steel400 shall be nominal size DN400
- Q: Butterfly valve D71X-16 and D71X-16Q what is the difference?
- The two difference is that the body of the material is not the same, 16 behind with no sign, expressed as a default, is carbon steel (usually C), if you need to specify material, just behind with symbols, such as Q nodular cast iron, stainless steel P.Butterfly valve refers to the closure of parts (valve or butterfly plate) as the disk, around the valve shaft to achieve rotation and closing of a valve, the main cut off on the pipe and throttling role. Butterfly valve headstock is a disc shaped disc, in the valve body around its own axis of rotation, so as to achieve the purpose of opening or closing or regulation. Butterfly valve used in furnace, coal gas, natural gas, liquefied petroleum gas, city gas, hot and cold air, chemical smelting and power generation environmental protection engineering system, conveying a variety of corrosive and non corrosive media pipeline, used to adjust and cut off the media flow. Butterfly valve categories are: handle butterfly valve, turbine butterfly valve, pneumatic butterfly valve, electric butterfly valve and so on.
- Q: I have a good set of #142 Pontiac heads with small diameter valves. I want to have the heads enlarged to accept the larger Pontiac valves, and I have the larger exhaust valves out of #13 heads and the larger intakes from 6X8 heads. The valves appear ok and shiny on the stems
- Roll the valves by the stems on a perfectly flat table. If there is no wobble, your valves are most likely not bent. Take them to a machine shop and have them checked for imperfections and reground and they'll be good as new.
Send your message to us
Butterfly Valve on Sale with Worm Gear Actuated Flange Triple Eccentric
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 1000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
