Brass Ball Valve Reduce Port with Steel/L HandleXBV-05
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 10000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Manual Wafer Ball Valve Description：
A ball valve is a valve which can be used for isolating or regulating flow. The closing mechanism takes the form of a disk. Operation is similar to that of a butterfly valve, which allows for quick shut off. Ball valves are generally favored because they are lower in cost to other valve designs as well as being lighter in weight, meaning less support is required. The disc is positioned in the center of the pipe, passing through the disc is a rod connected to an actuator on the outside of the valve. Rotating the actuator turns the disc either parallel or perpendicular to the flow. Unlike a ball valve, the disc is always present within the flow, therefore a pressure drop is always induced in the flow, regardless of valve position.
2.Main Features of the Manual Wafer Ball Valve
a)Cast hole. Flange connection meet ANSI 125/150# DIN PN10/16 BS4504 PN10/16 in the meanwhile.
b)Soft seat. Replaceable. Increase of service life.
c)Double half shaft without pin.
d) Square and short neck. Easy to stick scutcheon and cost saving.
3. Manual Wafer Ball Valve Images：
4.Manual Wafer Ball Valve Specification：
5.FAQ
1. What is manual wafer ball valve?
A: Wafer style is the more common of the two and is less expensive than the lug style. The wafer style ball valve is just about the standard. It ís so common that no one even bothers to use the word "wafer" when ordering a ball valve. It is taken for granted that if a ball valve is ordered, a wafer style will be received.
2. How about the Installation of the Wafer Style Ball Valve?
A: Butterfly valves are installed by inserting the valve between two flanges using bolts or studs and nuts to hold it all together. This type of installation, of course, makes it impossible to disconnect just one side of the piping system from the valve. That benefit is received using the lug style valve.
3. What is the working principle of manual wafer ball valve?
A: A ball valve is from a family of valves called quarter-turn valves. In operation, the valve is fully open or closed when the disc is rotated a quarter turn. The "ball" is a metal disc mounted on a rod. When the valve is closed, the disc is turned so that it completely blocks off the passageway. When the valve is fully open, the disc is rotated a quarter turn so that it allows an almost unrestricted passage of the fluid. The valve may also be opened incrementally to throttle flow.
- Q: Standard and specification for pressure test of valves
- Welcome to Beijing Shan'er pipeline control components Co. Ltd. consulting
- Q: What is the difference between the adjustable range of valve 50:1 and 100:1?
- One is 50 times, and the other is 100 times.
- Q: What does the whole copper valve mean?
- The whole valve is made of copper material. In addition to the ceramic core.
- Q: What's the difference between valves and valves without valves?
- The difference between a valve with and without a valve is that it has the advantage of having the valve exhaust. The advantage of the valve is that it can control the amount of exhaust and prevent the discharge of other fluids.Valve (Famen) is a control component in the fluid delivery system. It has the functions of closing, adjusting, guiding, preventing reverse flow, stabilizing voltage, shunting or overflow and releasing pressure.Valves used in fluid control systems, from the simplest stop valve to a very complex automatic control system used in a variety of valves, a wide range of varieties and specifications. Valves can be used to control air, water, steam, a variety of corrosive media, mud, oil, liquid metal and radioactive media and other types of fluid flow. The valve according to the material is divided into cast iron valves, cast steel valves, stainless steel valves (201, 304, 316), chrome molybdenum steel, chromium molybdenum vanadium steel valves, valve, dual phase steel valves, plastic valves, non-standard customized valve material etc..
- Q: Valve difference
- Valve difference, or you should ask the classification of valves, valve classification, there are several sub methods, some according to the model, and some are by use, then each kind of valve is divided into several categories and models. Take the trap for example, it is a kind of valve, and then it is divided into steam traps, air traps, float traps, and so on. If you really want to know the difference between the valve you search the Internet under the classification of the valve, there are a lot of articles, or you directly to the trap inside www.ssfmsh find an article on the valve type article, can not give you a specific address, is not allowed here. You work hard, go find kazakhstan. I hope my answer will be helpful to you.
- Q: The expert can tell me how to install this valve, and what fittings to use on both sides
- It looks a bit like the butt weld butterfly valve. The two sides are welded to the pipe. There is a step on either side of the valve. Overhead welding
- Q: What does the "Z45T-16" valve mean?
- Z - gate valve4 - flange connection5 - Dark pole, stem non lifting (gate valve structure)T - copper alloy, valve sealing face code16 - pressure code, 1.6MPaMaterial code for grey cast iron valves of nominal pressure less than or equal to PN16 shall be omitted in model preparation.May refer to JB/T 308 valve model compilation method
- Q: Look at the flow chart, some of the valves are marked with FV, and some are marked with XV. What does that mean?And what do you mean by the Cv value on the valve nameplate?I hope the heroes give a clear explanation ah, it is best to give an introduction of this knowledge of the web site oh.Thank again.
- FV or LV on the flow chart, which represents the instrument bit number, FV is flow valve, and LV is level valve.The valve on the nameplate CV value, it is a measure of the size of the valve flow, it is the concept of 40 - 60 degrees Fahrenheit in the water, the pressure drop of 1 psi, in a valve opening per minute flow through the valve (U.S. gallons).
- Q: How to open the gas valve with drawings
- It's different from place to place. Some are pulled out half, and some are pulled out. Third: in the following there is a black disk like thing, commonly known as the gas sound core. This one is the same as the second one, half or all
- Q: What is the KVS in the valve parameter?
- The valve Kvs is to reflect the passing capacity of the valve, which is defined as the pressure at both ends is 1bar, through the flow of the valve, Kvs is a characteristic parameter of the valve, and valve structure, is a constant value.
Send your message to us
Brass Ball Valve Reduce Port with Steel/L HandleXBV-05
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 10000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
