Black & White PE Protective Film S80-60BW
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT Or LC
- Min Order Qty:
- 10000 Square Meters m²
- Supply Capability:
- 10000 Square Meter Per Month m²/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Application: Painted stainless steel is mostly protected with transparent color PE protective film, which will show their original colors. PE protective film will protected the steel from dirt and scratch during production, transportation and installation.
2. Transparent color, transparent blue color, black & white color, white color, red color and so on available as per customers' requirements.
3. The choice of surface protective film depends on the surface: material and roughness. Tell us what surface you want to protect and we will recommend proper film to you.
Technical Data of Black & White PE Protective Film S80-60BWItem Number: S80-60BW
Carrier: PE (polyethylene) film
Thickness: 60micron (0.06mm)
Peel Adhesion: 80g/25mm
Adhesive: solvent acrylic
Color: back & white
Temperature Resistance: 60C 48hours no residue
Elongation: ≥250%
Inner Diameter: 3" (76mm)
Length: within 3000meter
Widh: within 1.5meter
Recommended jumbo roll size: 1.0m x 1000m
Black & White color PE protective film printed with logo on white color side also available
Packing of Black & White PE Protective Film S80-60BW
Wrapped with kraft paper or carton.
Remarks of Black & White PE Protective Film S80-60BW
A. The data above are typical results and subject to change without notice.
B. Tolerance: 5%
C. The products should be stored at room temperature and be kept away wet and/or heat source.
D. It is essential, the surface of film must be clean, dry, and free of grease and oil.
E. The users should take test and do trial-application on the above product before coming into application so as to witness and ensure suitability for their special purpose and technique
- Q: What are the differences between PE protective film and PE release film?
- PE protective film is used for the primary protection of electronic products when they leave the factory while PE release film is used as disposable consumable to protect the raw materials when wastes is discharged during processing.
- Q: Fire door finished surface with a layer of protective film is not good to tear
- 1, it is recommended to tear a corner, in the membrane and the door at the sticky point, pour alcohol, slowly tear.2, or with hot towel hot compress, use the hair dryer blow, also can more easily tear off.3, boiling water method. Suitable for steel, stainless steel, wooden can not use this method.4. Iron with iron. All doors fit.
- Q: Import PET protective film has those good introduction?
- Organic or inorganic glass lenses, various metal, electroplating plates, stainless steel, aluminum profiles, steel plastic profiles, aluminum plastic panels, glass panels, various types of paint panels, high-grade furniture, stone and other materials surface protection
- Q: What are the materials used in the production of aluminium protective films? What's the harm to life?
- Adhesion is good, easy to paste, easy to peel. The pressure-sensitive adhesive has good stability and does not cause any adverse effects on the surface of the product to be affixed.
- Q: Cell phone protective film on the small label to tear off the top, as well as how to remove plastic glue?
- The physical properties of ethanol are mainly related to the properties of low carbon straight chain alcohols. The hydroxyl radical in the molecule can form hydrogen bonds, so the viscosity of the alcohol is large, and the organic compounds with similar molecular weight are not so great
- Q: What's the difference between the film with by Cheyishang company and the ad film on buses, the protective film coated on new cars as well as other kinds of film?
- There are great differences. The ad film used on buses would curl after using for a long time. The adhesion strength of its backing gum is not good enough. And the protective film coated on the paint of new cars is usually transparent or white. It's too thin that the protective effect is not good. Glue and its residue may remain when tearing it off after a long time. And it has poor ductility.
- Q: Why should tear off the protective film on kitchen ventilator?
- The protection film is made of plastics. You should tear it off in case it fires.
- Q: Mobile phone protection film paste, and then ripped off, but also paste it? How should I post it?
- Not recommended. Because of the tear, his stickiness is gone. And they're all stuck with dust. Bad screen for mobile phones. If you want to post it. Prepare clean, small, clean rags.
- Q: How to remove the protective film on the security door?
- I suppose you can't remove the film because you didn't remove it immediately when you bought the door. You can find whether there is a part where the film curls. Apply some essential balm (or other oil) to the part and peel the part off at the same time. Repeating it for several times, you will find it's getting easier to peel. All you need is patience!
- Q: What are the differences between PE protective film, PET protective film and PVC protective film?
- PE refers to polyethylene. It's commonly used in protective films, featuring low price, softness, excellent ductility and environmental friendliness. Generally speaking, products made from this kind of material must pass the ROHS environmental pollution tests stipulated by European Union. Its disadvantage is poor whether resistance. It's not suitable to be used at temperature more than 60℃. PVC refers to polyvinyl chloride. Its features are good softness and whether resistance. And its disadvantage is non-environmental-friendly. Thus many big international brands rarely use this kind of material. Products made from this kind of material are mainly used for anti-static protection or as the surface of wooden stereo. PET refers to polyester. Its major property is good whether resistance which makes it resistant to high temperature of 100℃ to 150℃, hardness and flatness. And its disadvantage is that it can't be used on angular products.It's mainly used in die cutting.
1. Manufacturer Overview
| Location | Zhongshan, China |
| Year Established | 2004 |
| Annual Output Value | US$ 10 Million |
| Main Markets | 20.00% North America 20.00% South America 10.00% Eastern Europe 10.00% Southeast Asia 10.00% Northern Europe 10.00% South Asia 10.00% Western Europe 5.00% Africa 5.00% Mid East |
| Company Certifications |
2. Manufacturer Certificates
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period |
3. Manufacturer Capability
| a) Trade Capacity | |
| Nearest Port | Shenzhen Port |
| Export Percentage | 10% |
| No.of Employees in Trade Department | 50-100 People |
| Language Spoken: | English; Chinese; |
| b) Factory Information | |
| Factory Size: | Above 30,000 square meters |
| No. of Production Lines | Above 3 |
| Contract Manufacturing | protective film |
| Product Price Range | High; Average |
Send your message to us
Black & White PE Protective Film S80-60BW
- Ref Price:
-
- Loading Port:
- China Main Port
- Payment Terms:
- TT Or LC
- Min Order Qty:
- 10000 Square Meters m²
- Supply Capability:
- 10000 Square Meter Per Month m²/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
