Art no. HT-TS1024 ceramic knife,special color
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 PCS
- Supply Capability:
- 100000 PCS/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Set includes:
6-inch carving knife,1.8mm
3-inch paring knife,1.6mm
Blade:zirconia
Handle:ABS+TPR
Packing:with color box
You can choose the handle color you like
Zirconium material keeping 90° hardness just second to diamond which give the ceramic knife its outstanding sharpness and edge retention
Ergonomically shaped ABS + TPR handle in any color which keep the ceramic knife lightweight and colorful
Features:
Matte finished blade made of zirconium oxide (also calledzirconium)
Zirconium material keeping 90 degrees hardness just second todiamond which give the ceramic knife its outstanding sharpness andedge retention
Customized company names or logo on blades and packing ways arewelcomed
Advantages:
Transfers no metallic taste or smell to food
Has no acid and alkaline reaction with food
Lifespan is 10 times longer than conventional steel knife
Easy to clean up to prevent bacteria growth
Maintenance:
Only use plastic or wood cutting board
As with only knife, avoid dropping, throwing or generalmisuse
Avoid using the ceramic knife to cut seeds, bones, frozen foodor other hard product
Not flexible, don't use it to smash garlic, open cans orattempt to bent it in any way
Hand wash only
Do not attempt to sharpen the ceramic knife yourself unless youhave access to sharpener specific to ceramic knives
- Q: Are all self locking knives controlled? The knife is small again?
- You know, this is in China, the tube is not the document is not the final say, it is the banditsAccording to the truth below 8cm is not the knife knives
- Q: Excuse me, master, difference, white steel cutter and tungsten steel knives advantages, what are the disadvantages?
- Is the cost difference. White steel knife mostly refers to high-speed steel cutting tools, high-speed steel (HSS - HIGH SPEED STEEL) is the most common material SKH9, hardening heat treatment to about HRC64. The cost is low by cutting tool steel, the hardness of the workpiece is low, is the most traditional tool. The car is tungsten steel knife the hardness of HRA90-93, harder and more than high-speed steel tool with cutting force, service life is long, but also more expensive.
- Q: Cubic boron nitride cutting tools for processing what materials
- Cubic boron nitride, commonly known as CBN, is a tool hardness second only to diamond material.It has high hardness, good red hardness, and almost all of the metal poor compatibility, but at the same time, poor toughness, non impact, easy to collapse.According to the above characteristics, cubic boron nitride, suitable for quenching materials (high hardness), high silicon steel, non-ferrous metal finishing and semi finishing.In particular, because of the incompatibility between CBN and C in cast iron, CBN is widely used in high speed finishing of iron castings.
- Q: I know that there are two numbered Rules, one of which is T0101, T0202, T0303, T0404, etc.There is a T0101, T0102, T0103, T0104, such as the number, under the advice of the two numbersCan it be mixed? If you can, how to determine the knife mark?
- Yes, don't get too caught up in it. The tool and knife mark are not necessarily linked, the tool number is fixed, the knife mark is alive.
- Q: What is stainless steel kitchen knives
- Stainless steel, an alloy.
- Q: How to improve the service life of cutting tools
- In general, turning plastic metal materials with large, should take a larger rake angle, cutting in mild steel, the angle value is slightly smaller, but still maintain a certain value, cutting steel, angle of small, and in the cutting of hardened steel hardness is particularly high, hard alloy tool general with negative rake angle or zero rake angle. But in the turning of the copper alloy, the rake angle of the tool is big and easy to gnaw the knife phenomenon. In general, when the car, the front and rear angle to take some larger, rough car, in order to the strength of the tool, the front and rear angles to be small.
- Q: What is the most important influence on the cutting tool?
- The feed is small, the flank wear is large, the tool life is greatly reduced. Feed, cutting temperature increases, the flank wear will increase, but the cutting speed than the impact on the tool life is small, of course, a large amount of feed, processing efficiency is also high.
- Q: What is the relative motion between the tool and the blank?
- Hobbing? Gear manufacturers know
- Q: Selection principle of tool rake angle
- The other tool forming cutter and the angle of influence of blade shape, in order to prevent the edge distortion, anterior horn often take a smaller, even taking the gamma = 0. However, the cutting conditions of these tools is not good, should be under the premise of ensuring the cutting edge forming precision, try to increase the anterior horn, such as increasing the front angle of thread lathe tool and gear hob.
- Q: Woodworking engraving machine commonly used tools which?
- 1, flat knife is a common woodworking engraving machine tool. This tool is suitable for small precision embossing processing, carving out the edge of the product is smooth and beautiful. To do a large sculpture carving time. A 2 knife, knife is relatively common, commonly used to carve characters. It cuts out the edge of the material for the straight edge, which is commonly used in PVC, acrylic cutting word. 3, milling cutter is the most common tool in woodworking engraving machine, milling cutter is divided into many kinds according to the shape. For example, in the cutting of acrylic, density board when the use of double helix milling cutter, cork, density board, solid wood, acrylic materials, such as large deep processing of a single edge of the spiral ball end milling cutter. High density board, solid wood doors, furniture processing when the use of edge milling cutter. Of course, many manufacturers will tool according to the special requirements of many customers to make a special tool, for example, is more suitable for long chip spiral milling cutter cutting density board chip. Round bottom knife is more suitable for small precision relief processing. Woodworking engraving machine is one of the important chencan mechanical products, widely used in doors, furniture production enterprises, as well as exquisite tea sets, sofa legs, tiger wood line, PVC, hollow partition acrylic engraving industry...
Send your message to us
Art no. HT-TS1024 ceramic knife,special color
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 PCS
- Supply Capability:
- 100000 PCS/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches