• A Cheap Price , Ball Valve Price , Glove Valbe , Gate Valve , Butterfly Valve System 1
  • A Cheap Price , Ball Valve Price , Glove Valbe , Gate Valve , Butterfly Valve System 2
  • A Cheap Price , Ball Valve Price , Glove Valbe , Gate Valve , Butterfly Valve System 3
A Cheap Price , Ball Valve Price , Glove Valbe , Gate Valve , Butterfly Valve

A Cheap Price , Ball Valve Price , Glove Valbe , Gate Valve , Butterfly Valve

Ref Price:
get latest price
Loading Port:
China main port
Payment Terms:
TT OR LC
Min Order Qty:
100 pc
Supply Capability:
10000 pc/month

Add to My Favorites

Follow us:


OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

 

1.Structure of Gate Valve Description

A gate valve, also known as a sluice valve, is a valve that opens by lifting a round or rectangular gate/wedge out of the path of the fluid. The distinct feature of a gate valve is the sealing surfaces between the gate and seats are planar, so gate valves are often used when a straight-line flow of fluid and minimum restriction is desired. The gate faces can form a wedge shape or they can be parallel. Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the petroleum industry. For extremely thick fluids, a specialty valve often known as a knife valve is used to cut through the liquid. On opening the gate valve, the flow path is enlarged in a highly nonlinear manner with respect to percent of opening. This means that flow rate does not change evenly with stem travel. Also, a partially open gate disk tends to vibrate from the fluid flow. Most of the flow change occurs near shutoff with a relatively high fluid velocity causing disk and seat wear and eventual leakage if used to regulate flow. Typical gate valves are designed to be fully opened or closed.When fully open, the typical gate valve has no obstruction in the flow path, resulting in very low friction loss.

 

2. Main Features of the Gate Valve

• Valve body cavity using non-toxic epoxy resin,both inside and outside flashboard completely is coated with rubber

•  Free of water pollution

• High manufacturing accuracy

• High strength

• Environmental protection and energy saving

• Good visual effect

 

3. Images

 

A Cheap Price , Ball Valve Price , Glove Valbe , Gate Valve , Butterfly Valve

A Cheap Price , Ball Valve Price , Glove Valbe , Gate Valve , Butterfly Valve

4. Gate valve Specification

 

A Cheap Price , Ball Valve Price , Glove Valbe , Gate Valve , Butterfly Valve

A Cheap Price , Ball Valve Price , Glove Valbe , Gate Valve , Butterfly Valve

5.FAQ

1. What's are the characteristics of gate valve?

The distinct feature of a gate valve is the sealing surfaces between the gate and seats are planar, so gate valves are often used when a straight-line flow of fluid and minimum restriction is desired. The gate faces can form a wedge shape or they can be parallel. 

2. What is the work principle of gate valve

 The gate faces can form a wedge shape or they can be parallel. Gate valves are primarily used to permit or prevent the flow of liquids, but typical gate valves shouldn't be used for regulating flow, unless they are specifically designed for that purpose. Because of their ability to cut through liquids, gate valves are often used in the petroleum industry. 

3.  What is the structure?

Bonnets provide leakproof closure for the valve body. Gate valves may have a screw-in, union, or bolted bonnet. Screw-in bonnet is the simplest, offering a durable, pressure-tight seal. Union bonnet is suitable for applications requiring frequent inspection and cleaning. It also gives the body added strength. Bolted bonnet is used for larger valves and higher pressure applications.

 

Q:What is the difference between gate valve and gate valve? Is it the same valve?
The valve is driven by the valve stem to make vertical lifting of the plate inside the valve body.Gate valve is the same reason. The gate valve and gate valve have steel gate, parallel double gate and so on.So the gate valve and gate valve are the same valve. It's just a different name.
Q:What are the working principles of the electric gate valve?
Ordinary type electric valve should be equipped with the control box, the motor is the true story and the inversion, and in general to a trip signal signal is normally open and normally closed, closed in place are normally open and normally closed two points according to their own needs wiring, three lines and then open and close control of the line of control there are also 4 lines to control some manufacturers, as well as the valve position, some three lines connected with the potentiometer, some installed valve position transmitter is connected with two lines, and over torque protection fault signal.
Q:What is wire feed gate valve? What do you say in French?
It should be the wire gate valve. Refers to the valve body with internal thread or external thread, and pipe thread connection. Also called thread valves, threaded valves, valves within the toothFlange gate valve is connected to the flange gate valve, this connection is the most common wayThe main difference is the connectionI only know their English, I'm sorry I can't help youBox thread valveFlange valve
Q:Installation and operation instructions of knife gate valve
1. knife gate valve installation, check the valve cavity and sealing surface and other parts, not allowed to dirt or sand adhesion;2. bolts of connecting parts must be tightened evenly;
Q:Z45T-10 what kind of material is the gate valve?
JB/T 308 regulation3.7.4 nominal pressure of less than 1.6Mpa gray cast iron valve body material code, in the type of preparation to be omitted.So its body material is gray cast iron, the sealing surface is copper alloy
Q:Gate valve, butterfly valve, ball valve advantages and disadvantages? What are the usual valves?
Steam traps: in steam, compressed air and other media, there will be some condensation water formation, in order to ensure the efficiency and safety of the device operation, should be timely discharge of these useless and harmful to the media, to ensure the consumption and use of the device. It has the following functions: 1. It can quickly eliminate the condensed water; prevent leakage of steam; remove air and other non condensable gases.Pressure reducing valve: by adjusting the inlet pressure to a certain outlet pressure, and rely on the energy of the medium itself, so that the outlet pressure automatically maintain a stable valve.Check valve: also known as reverse flow valve, check valve, back pressure valve and one-way valve. The valves are automatically driven and closed by the flow of the medium itself, belonging to an automatic valve. The check valve is used for piping system, the main function is to prevent the backflow of medium, prevent the reverse of pump and drive motor, and release the container medium. The check valve can also be used to provide a supply to the auxiliary system where the pressure may rise above the system pressure. It can be divided into swing type (rotating by gravity center) and lifting type (moving along the axis).
Q:Soft sealed gate valve and hard sealing gate valve which good?
If the caliber, material and pressure levels are the same, the current market price is still soft sealed gate valve, about 20-30%.
Q:Why does the centrifugal pump start and stop in the case of closing the gate valve?
After the valve is closed to stop the cause of centrifugal pump outlet valve is closed to stop the pump to prevent the flow back into the pump, impeller, impeller in reverse, part of the mechanical seal in the pump pump impeller reversal will have adverse consequences, serious damage to the centrifugal pump, to close the valve after the shutdown.
Q:What is the difference between gate valve 41h-16c and 41w-16p?
The difference between 41h-16c and 41w-16p is that the material of the valve body and the material of the sealing surface are different.According to the provisions of the JB/T 308-2004 valve type programming method:H== sealing surface material: Cr13 stainless steelC== body material: carbon steelW== sealing surface material: body, that is, with the same material bodyP== body material: chrome nickel stainless steel
Q:What is plug welding gate valve?
Plug connection pipeline welding mode safety gate valve

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range

Send your message to us

This is not what you are looking for? Post Buying Request

Similar products

Hot products


Hot Searches