352926 Tapered Roller Bearigs Single Row Bearing
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 500000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specificatioin of Taperder Roller Bearings:
The tapered roller bearing is to bear the combination of radial and axial load but mainly afford radial load. The loading capibility is determined by the raceway angle of outer ring, the larger angle afford larger load. This kind of bearings can be seperated and it can be divided into single-row and double-row tapered roller bearings by the number of columns. The clearance for single-row tapered roller bearing should be adjusted by the customers when installation. For the double-row tapered roller bearings,the clearance has already set by the manufacture before ex-factory. Tapered roller bearing has taper shaped inner ring and outer ring raceway,and the roller elements arrange between them. All projection lines from the surface of rollers meet at the same point on bearing axis. This design makes tapered roller bearings particular suitable for combined (axial and radial) loads.The axial loading capacity is determined by the contacting angle α, the bigger angle for α, the larger axial loading capacity is. Tapered roller bearing is usually a seperated bearing, that is,the inner ring assembly including roller and cages, is seperated installed with the cup.
Taper roller bearings are mainly used for radial and axial joint load with radial load as main subject. Axial load capacity relies on raceway angle of outer ring: the bigger the angle is, the bigger the bearing capacity is. Outer ring can be separated and can be easily assembled. During installing and using process, axial clearance and radial clearance and radial clearance can be adjusted and pre-interference installation can be allowed.
Product application:
In many applications tapered roller bearings are used in back-to-back pairs so that axial forces can be supported equally in either direction.
- car and vehicle wheel
- mining equipment
- moderate speed
- engine motors
- axle systems
- construction
- agriculture
- reducers
- gear box
- Q:There are many kinds of tapered roller bearings, because of work requirements, test the external size is qualified, I want to make a test, to test the bearing is qualified, mainly inside and outside diameter and inside and outside the ring height tolerances, diameter ranging from 50mm--80mm, score less, look forward to your help, I thank you there are 322163311532215 main bearings, 313113002
- Less points, huh, huh?Bearings are tested with a dedicated bearing inspection instrumentTable seat:Outside diameter D913Internal diameter D923Height G904With standard and special micrometer (usually microkators and leverage comparator)Each inspection procedure has the corresponding inspection instructionYou can provide the job instructions free of charge to your bearings suppliers as a project to review their process controlAs for the instrument, you should pay for it even if your supplier offers itIf you buy the bearings in the retailers, then you have to pay for them yourselfThe work instructions may also have to be replaced by money
- Q:Taper roller bearings limit speed, according to what to calculate, there is no formula for what?
- First of all, different types of tapered roller bearings, the limit speed is different. Bearing on catalog.Second, the calculation of bearing limit speed is calculated by computer simulation of bearing manufacturer. It is very complicated. Mainly based on frictional heat generation and cage strength limit.So, we use bearing technology or design personnel, only need to control your speed in the following catalog bearing manufacturers can.In addition, oil lubrication is better than grease lubrication at the same speed.
- Q:What are the general uses of tapered roller bearings?
- At the time of greater radial load and axial load
- Q:you master good! Ask a question about the use of tapered roller bearings: a mechanism using a double row tapered roller bearings, but did not buy this model, can use two single row tapered roller bearing together instead of double row?
- 2, the clamping way is: double row bearing inner ring is double row, or outer ring double, determines when you install the inner ring or outer ring is clamped, clamped, if you want to replace with the two row, when combined with the clearance you need to consider the ring, you should adjust the clearance and is placed on the inner ring, or on the outside, too that depends on your way of clamping;
- Q:Tapered roller bearing: Bearing expert why burned or locked
- 1, improper choice of bearing clearance.For example: C3 group should be selected for clearance, and the actual use of ordinary group clearance. Because when the bearings work will continue to accumulate heat, shaft diameter and inner ring and outer ring rolling body will swell, because good radiating condition of expansion is relatively small, the whole bearing clearance becomes small, or even negative clearance larger.At this time, stress increases between the body and the rolling roller pressure, lubrication conditions decreased, there will be the phenomenon of boundary lubrication or even local steel on steel friction, so the temperature continues to rise, the base oil in lubricating grease evaporation, so lead to vicious spiral bearing overheating burned, rolling annealing into blue black color, then bearing the friction increasing roller holder to stop COLLOPSE bearing lock.
- Q:What does "tapered roller bearing" suffix "A" mean?
- Tapered roller bearing suffix AA - angular contact ball bearings with a contact angle of 30 degreesA5 - angular contact ball bearings with a contact angle of 25 degrees
- Q:The device is a vertical axis vertically arranged in the bearing chamber, the upper shaft without suspension, supported by bearings, shaft bearings are installed at the bottom of the outdoor rotating parts weighing 50 kg, the two ends of the shaft are used in single row tapered roller bearings, the bearings between the length of 30 meters. The rotation speed of the shaft is 480r/min. The device is suspended on a rotating turntable and is subjected to centrifugal force during operation...
- Thrust bearing words. Thrust roller bearings can be used,
- Q:What is the size of tapered roller bearings 352214?
- Bearing type: tapered roller bearingNew model: 352214Old model: 97514EInternal diameter (mm):70Outside diameter (mm):125Width (mm):75
- Q:Can tapered roller bearings be installed in a vertical direction? In a vertical direction rather than in a horizontal direction..
- Whether horizontal mounting or vertical installation, the axial direction is axial and radial is radial
- Q:There is a slot in the inner ring of tapered roller bearings, right? Is the roller in the slot?
- There is a slot in the cone... The ball is placed in the slot. Handan, north, LiAskIs there a gap between the roller and the slot?Can I move axially?Chasing the answerThere is a certain clearance between them. It is not very large. It is caused by the force...
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
352926 Tapered Roller Bearigs Single Row Bearing
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 500000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords