Stainless Steel Cutters

Hot Products

Drilling Tools Best Quality Button Bits Top Hammer Rock Drilling Tools

Mill cutting tool Tungsten carbide mill cutting tools milling cutter tungsten milling cutter

Turning Tools Metal Lathe Cutting Tools Diamond Cutting Tool

BFL-Micro Grain Rough End Mill Coated Flute Rough CNC Milling End Mill Cuter

CBN Cutting inserts for air-conditioner compresser

Tungsten carbide blade knife machine tools on sale

95 Degree New B Type CNC External Turning Holders of BCLNR2525M12 or BCLNR2020K12

tungsten carbide inserts for cutting tool

Carbide Turning Inserts TNMG160408 tungsten carbide inserts

Indexable face finish milling cutters cnc alloy steel face cutting tool

FAQ

What is a lathe for aluminum

Use a diamond knife if you want a tall light..I hope my answer will help you

The lathe tool, milling cutter, planer, bit, boring tool, the cutting fluid which is used for machining, the effect is good?

Turning, milling, planing tool, drilling, boring cutter, these are as part of the carbide, carbide processing, have a more targeted, is one of the microemulsion cutting fluid.

What material is used to heat up after welding?

Not only copper, but also a deoxidizer, and the most commonly used is the pine powder. There is also a certain level of operation, because I've seen a lot of welding common car knives, and the alloy head always falls off at work.

How do you know the type of car knife

Forming tool. The shape and size of the shape and size of the cutting edge of the machine tool are the shape and size of the tool blade. In CNC turning, the common forming tool has small radius circular arc tool, non-rectangular slot machine tool and threading tool. In nc machining, it should be used as little or no forming tool. The choice of the turning tool of the machine clip Machine clip indexable nc tool common varieties, more than 2000 kinds of specifications, and requirements in a variety of indexable carbide insert, ceramic knives and other material of the blade to match. There are various kinds of milling cutter, hole cutting tool, lathe tool and compound cutter (drilling, expanding, boring, spot). In order to reduce the time and convenience of changing the knife, to facilitate the standardization of machine processing, the CNC turning process should be used as the machine clamp knife and blade. CNC lathe is used in the form of rotary tool.

What is the reason for the hard alloy blade to be welded to the pole?

Welding quality problem. Hard alloy tool head, tool bar belongs to foreign metal welding, now mainly has: gas welding brazing and high frequency welding. Gas welding brazing is using oxyacetylene flame (or oxygen propane etc) welding, heat tool rod alloy tool bit, using the copper wire dips in flux flux (copper, borax boric acid equal parts mixed flux, borax) a welding process, welding copper wire melting point is lower than the tool holder, segment, using the capillary action for brazing welding effect. The flame leaves the molten pool in the welding process, and the protection of the air is not strong enough to cause the welding. It is necessary to clean up the welding quality before it can be soldered. High frequency brazing is the use of silver soldering terminal (copper welding pieces of external coating with silver) as a tool holder, cutting head solder, using high-frequency alternating current heating temperature, silver welding molten brazing welding effect. Incorrect selection of welding parameters and poor quality of silver welded plates will also cause the welding to be unstable. Before welding, tool tip is also cleaned up.

The difference between the threading tool and the external turning tool

When the rib is in the rib, it is a fan. The sharp corners of the knife should be the same as the thread's rib Angle, usually 60 degrees. The external turning tool is not required.

How to weld a car knife? How do you handle the welding fire

I put the knife in the pole and put it on the bottom of the pole. Don't burn the alloy. When the blade is red, the alloy is turning red. Where the copper is hot. Don't burn your ass, you'll have more experience...

What if oxygen welds don't stick

When welding the blade is heated to red, right amount into the solder powder (borax) and then put the blade in (blade had better put on the grinding wheel to welding surface treatment), and then heated to the blade dark red, copper electrode micro hot melt again after add borax in the joint between the blade to blade leakage amount, and will continue to heat the blade saw copper water seeping from below, you're done.