Tinplate Shearing Machine

Ref Price:

Loading Port:: China Main Port

Payment Terms:: TT or LC

Min Order Qty:: 1 Unit unit

Supply Capability:: 150 Units per Month unit/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Pneumatic Spot Welding Machine With Little Power Loss

Unsymmetry Argon(Arc) Welder

Welding Machine SZ-2T with Bench Type Cold Pressure

TIG-200 250 300 Welding Machine

NBC-250A 315A 500A Tap Welding Machine MAG Welding Machine

CUT-40 60 100 portable inverter Air Plasma Cutting Machine

NEW DODO-600 Fully automatic can body welder

100kw pipe Solid state HF welder high quality

High quality low price tinplate shearing machine

1) High quality Best service

2) Lower price 1 year warranty

3) Precise cut

1.Functions

GT1B5B Plate Cutter with Round Knife is used to massively cut tinplate or other sheet iron.

2. Main technical index:

Scope of application:

Maximum thickness of sheet iron(mm) --------------------------- 0.5

Maximum width of sheet iron(mm) ------------------------------ 1050

Minimum width of sheet iron(mm) ---------------------------------- 55

Power of motor(kw) -------------------------------------------------- 1.1

Size(mm) ----------------------------------------- 1500 × 1600 × 1105

Weight(kg) ---------------------------------------------------------- 1200

Q:Spot welder operation flow: The operation of the spot welding process can be divided into three stages: 1, 2, 3 stage compression stage of heating and cooling crystallization stage (welding between the electrodes will be pre pressurized, heated to the required temperature of welding parts, welding parts under pressure in the electrode cooling)

Q:When the spot welder is in use, the voltage of the line will be higher and lower. What can be done to solve it?: The single-phase AC spot welder should be used. The single-phase power supply of AC spot welder has destroyed the balance of power grid and seriously affected the normal operation of other power equipment. The inverter type spot welder is supplied by three-phase power supply, and its operation does not affect the three-phase balance of the power grid.The power factor of welding machine is an important index that affects the utilization ratio of power supply equipment. If the power factor of welding machine is doubled, the requirement of power supply capacity will be reduced by 1/2. Because the resistance welding machine outputs is the low voltage, the big current. Therefore, the inductance of the secondary circuit of the welding machine is obvious, so that the power factor of the AC resistance welder can only reach 0.3~0.5. The inverter type resistance welding machine outputs DC welding current, and the power factor of welding machine can be as high as 0.95. Therefore, the requirement of the power supply capacity of inverter type resistance welding machine is less than that of the AC welding machine of the same capacity as 1/2.

Q:Do welding materials need to be welded? What welding materials are needed for the spot welder and the welding machine respectively?: No solder is needed for spot welder, touch welding machine and intermediate frequency inverter welder

Q:Spot welding machine has a 200KVA, not because of the full load operation (only 1/10 of its power operation) now want to take in the power distribution cabinet on a 200A, don't know if I can start immediately after starting antihypertensive use, current will have impact on the grid?: There is no starting current of the electric welder, he is a transformer, a high voltage to low voltage and high current, must have a certain impact on the power grid, can bus in the cabinet in the installation of reactive power compensation device, can alleviate the fluctuation of voltage value, the general effect on the fluorescent lamp a little more

Q:Spot welding temperature is too high to deal with: It's pedal like. But the water pipe is also connected. However, the solder joint temperature is still very high. I also adjust the temperature control of the controller, but still the same as usual, welding contact points are black, welding surface also appeared a lot of holes, how should I deal with it?

Q:Use 12 volt batteries.. Direct welding needle is used as spot welder.. Electric spot welding mobile phone battery.. Is it feasible?.: If the electrode is in place, it may be ok

Q:Is the spot welder the same as the riveting welder?: Quite different。 Spot welding machine is to use the positive and negative electrode short circuit to produce short circuit current to dissolve metal parts. A riveting machine uses a punch similar to a punch pin to rivet two pieces together in a small package. Two kinds of equipment welding process is different, according to the welding workpiece to decide.

Q:Without welding spot welder welding head is what reason?: There are quite a few reasons. Mainly includes the following aspects: 1, 2, welding material; welding structure; 3, welding material structure of the workpiece; 4, spot welding power supply technology level, such as the discharge stability, welding time adjustment; 5, the maintenance of spot welder welding head grinding, including methods and frequency. Maybe these. The 1-3 point is decided by the welding material, structure, welding effect and so on. Generally, the workpiece is fixed, and the material and structure are right. So there is nothing to change. Fourth consider using inverter DC welding machine, energy concentration, welding stability, short cycle time, the long-term benefit of welding head life. Fifth, the formulation of standard grinding, correction frequency and method of guidance, how many points welding, grinding once, with what grinding and so on.

Q:There is an old spot welder, can not see the label, probably more than 40 streams, due to voltage instability, would like to add a voltage regulator, I do not know can play a role? Consult a master to help, first thank you!!!: Voltage regulator is used by small electrical appliances, welding machine is not good

Q:I want to know how the spot welding machine controls the welding time and the rest time. Is it controlled by PLC?. Hope expert pointing one or two.: Now the general control is PLC. In addition to time, there are currents, pressures, etc., which are controlled.

We specialize in designing and manufacturing series of fully automatic and semiautomatic can making machines, toilet soap production equipment, capacitor equipment, filter equipment and other machines. Our product lines are suitable for many sectors, such as food cans, chemicals, and petroleum industry. Our company has owned many honors and recognitions from customers because of our excellent product quality and perfect after-sales service. We warmly welcome all customers to visit our factory and test our products.

1. Manufacturer Overview
Location	Jiangxi, China
Year Established	2000
Annual Output Value	Above US$100 Million
Main Markets	Southeast Asia1.33% .Africa1.65% .Oceania0.13% .Mid East0.38% .Eastern Asia0.63% .South Asia0.79% .Domestic Market95.09% .
Company Certifications	Honesty and High Quality Enterprise;

2. Manufacturer Certificates
a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability
a)Trade Capacity
Nearest Port	Jiujiang port,Shanghai port,Guangzhou port
Export Percentage	41% - 50%
No.of Employees in Trade Department	3-5 People
Language Spoken:	English, Chinese
b)Factory Information
Factory Size:	10,000-30,000 square meters
No. of Production Lines	Above 10
Contract Manufacturing	OEM Service Offered
Product Price Range	Average