ZJ1500 x 2.5 Slitting line
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 10 sets set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1.1 Raw material: car bon steel strip
1.2 Specification of raw material:
Thickness of steel strip 0.8 - 2.5mm
Width of steel strip 650 - 1500mm
Inner diameter of strip coil 508mm
Max weight of strip coil 15 tons
1.3 Finished Product
Inner diameter of strip coil 508mm
1.4 Slitting capacity
quantity of srip 20 strips
1.5 Max Line Speed 100m/min
1.6 Input Power: 380Volt, 3 phase, 4 lines, 50Hz.
1.7 Feeding Direction: Left side or right
II Technical flow:
Coil loader → Uncoiler → shovel board device → Feed Flattener → end shear → Centering device→ Slitter→ scrap winder → Accumulator →tension stand→ Recoiler→ Movable support→ Separating Presser → coil unloader
- Q: What is the arrangement principle of cutting order in machining?
- First principal second:First, the main surface is processed, and then the minor surface is processed.
- Q: Causes of retention of mechanical metal chip cutters
- Product cut tumor is unstable in the cutting process, it is time now, later, to a certain height, broken by the workpiece and cutting away and disappear, and then destroy the estate was born again and again. The surface of the workpiece is uneven and the surface roughness decreases. It also causes vibration during cutting and speeds up tool wear.
- Q: What are the differences between metal cutting equipment and metal processing equipment?
- Metal processing equipment is divided into many kinds, metal cutting equipment is one of the metal processing equipment, such as vertical lathe belongs to metal cutting equipment, but also metal processing equipment
- Q: Metal cutting machine tool manufacturing is mainly mechanical, machine, drilling machine, grinding machine etc.. Its safe operation
- Operators wear tight work clothes, cuffs tight, long into the cap, rotating equipment, disable gloves;
- Q: All the parts on the machine must be machined by metal cutting, right?
- Some standard parts do not need to be machined, such as belts, bolts, nuts, gaskets, oil pipes for lubrication systems, etc., without machining.
- Q: How about the metal cutting parameters?
- When machining large, thin and slender workpieces, lower cutting speed should be used, and the end face turning should be faster than that of outside turningTaller.
- Q: What are the unsafe modes of metal cutting machine tools?
- Glove handling,don't wear protective glasses,feed too fast, the metal parts are too small to use hand feed.
- Q: Method of programming for metal cutting machine tools
- According to the processing mode is divided into 12 categories:Lathe, drilling machine, boring machine, grinder, gear cutting machine, thread cutting machine, milling machine, planer, broaching machine, EDM machine tool, machine tool, cutting, and other machine tools.
- Q: How is the cutting force calculated in a metal cutting unit?
- In metal cutting, the tool cuts into the workpiece and deforms the machined material and becomes the force required for the chip. This is called the cutting force.
- Q: What kinds of typical machine tools are involved in wood processing machinery? What's the difference between metal cutting and metal cutting?
- Wood processing equipment and metal cutting equipment have similarities and differences. Common points are: both the main movement and auxiliary movement of the cutting process, and drilling machine and lathe is completely metal cutting equipment variation. The difference is: the cutting mechanism is different, the tool used is different.
Send your message to us
ZJ1500 x 2.5 Slitting line
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 10 sets set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
