Slitting Line With Best Quality Best Price
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 100 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Features:
1. The production line is a thick metal coil leveling and cut into a massive of special equipment. Usually cited by the feeding car,uncoiler,pallet pressure device,leveling host activitiesacross the bridge,guide corrective device,length agencies,film equipment,shear,conveyor table,pneumatic discharge rack,hydraulic lift the composition of the pile material, material transport roller and hydraulic system,electrical control system, the concerted action of PLC control. The main hydraulic,pneumatic and electrical conreol components,cot to length system selected international brands.
2. This equipment is mainly used for processing cold-rolled carbon,stainless steel coil, and non-ferrous metal coil, configuration,six leveler to theentire pacification of long shear plate surface of the metal aluminum and other high coil.
3.According to customer requirements, the fine two leveler can be used early; fixed length sent to shear can be ordinary mechanical appliances collaborative action, digital variable frequency or AC servo technology; shears can be equipped with the ordinary machienry, hydraulic press type electromagnetic clutches,pneumatic clutch transmits power high speed gate shear, mobile tracking the chase cut and rotary flying shear machine. Supporting related molding machine can be used for a wider range extension.
Technical data of welded steel pipe mill
Model | CM12 pipe welding machine |
Diameter of Welded Tubes | 7-19mm |
Wall Thickness of Welded Tube | 0.2-0.5mm |
Speed of Tube Welding | 30-100mmin |
Power of Major motor | 15KW |
High Frequency Power | 60KW |
Progress of pipe production line
Raw material (steel coil) → uncoiling → shearing and butt-welding → material accumulating → passively leveling → mill-forming → high-frequency welding → removing burrs outside of weld seam → cooling → sizing → roughly straightening → fixed length cutting → run-out table
Main configuration of erw pipe making machine:
Uncoiler~Shear and end welder(prepared by customer)~Accumulator~Forming, welding, sizing unit~Pneumatic or computer-controlled length cutting saw~Run-out table
In order to offer you right model of pipe welding machine, please tell us the details as follows:
1. The material of pipes
2. The diameter of pipes
3. The wall thickness of pipes
- Q: A roll forming machine, rolling out of the length is always not up to a fixed size, not too small, that is, more than that, what is the cause?
- Yes, the width of the bearing plate can be a deviation from the length.
- Q: What is rolling forming processing?
- Rolling process is a kind of pressure finishing, which is a kind of cold plastic characteristic of metal under normal condition.
- Q: Improvement in rolling forming process
- Rigid force, 1000N-3000N, damage to the guide rail of machine tool transmission mechanism, seriously damage the accuracy and life of machine tools.
- Q: Introduction of roll forming process
- With the progress of technology and the development of production, more and more attention has been paid to the roll forming process.
- Q: What kind of material and what heat treatment are used for pressing roller (molding, feeding, cutting force, heavy load, heavy load) of sheet steel rolling machine?
- Non bonding wear of rolled material (especially stainless steel strip, etc.)
- Q: What is the surface rolling forming machine process?
- The rolling process using metal at room temperature, cold plastic characteristic, through the rolling tool is the rolling tool to put some pressure on the metal surface, so that the workpiece surface by plastic deformation, the height to the lower tissue slip, the surface roughness decreased.
- Q: Process mould for rolling forming process
- A movable wire plate, made of the same fixed wire plate, for relative reciprocating motion. Roll forming is the design of different structures on the plate rolling on the workpiece. Roll out all kinds of thread, convex ring, knurling, end chamfering, groove with different width and thickness as well as other required shapes.
- Q: Material and equipment for roll forming process
- Rolling process is a cold forging process, which can be used for rolling and forming a lot of materials. Among them, low carbon steel is a material commonly used in rolling forming, and non-ferrous metal is more suitable for roll forming.
Send your message to us
Slitting Line With Best Quality Best Price
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 100 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
