Silicon Bonded Silicon Carbon Alloy Ball

Ref Price:

Loading Port:: Tianjin

Payment Terms:: TT OR LC

Min Order Qty:: 20 m.t.

Supply Capability:: 1000 m.t./month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

CALCINED BAUXITE A

Gas Calcined Anthracite Coal made from taixi Anthracite

Calcined Bauxite Rotary Kiln Al2O3 85%

Calcined Bauxite Rotary Kiln Al2O3 86%

Metallurgical Grade Aluminum Oxide Al2O3 Powder

$Best Calcined Bauxite for Refractory Raw Materials$

Best Calcined Bauxite for Refractory Raw Materials

86% alumina 1-3mm calcined bauxite with low price

$80% Round Kiln Alumina Calcined Bauxite Refractory Raw Material$

80% Round Kiln Alumina Calcined Bauxite Refractory Raw Material

Silicon Carbon ball

At present, the iron and steel metallurgy enterprises usually adopt alloying out of the furnace to adjust the steel composition and use the common recarbonizer to adjust its carbon content. When the molten steel is under peroxy state, since the density of recarbonizer is small, it has poor efficiency of adding carbon. On the other side, it can’t sink into the molten steel and there is little possibility of acting with the molten steel, only can act on the top or on surface, so the recovery rate of carbon is low. Nevertheless, many steel enterprises try to resolve the problem by adding carbon cored wire, which increase the production cost and equipment cost, what’s more, it is much difficult t operate.

We has two production lines, the monthly production capacity is 1000 tons.

Specification

C	Si	S	P	H2O	Granules
20-30%	45-55%	≤0.12%	≤0.2%	≤0.5%	20-50mm

Q:what is the common materials for home fireproofing material?: 1, lumber core 2,decoration panel 3 , plywood 4 density board 5,chipboard 6 fireproof?panel, 7.gypsum board Hope to adopt my opinion

Q:What refractories are resistant to fluorine gas?: It is recommended to use fused-quartz brick, which will produce hydrofluoric acid fluorine (an acidic gas) when water vapors. It is cheap. While it is recommended to use silica?brick if it exceeds 1,200 degrees. So acidic refractory is an advisable refractory for using. It works well if the temperature is below 1200 degrees.

Q:How to divide fire resistant level of fire door?: The classification of fire resistant level of fire door: Grade A is not less than 1.2h. Grade B is not less than 0.9h. Grade C is not less than 0.6h. It is suitable for fire door with different levels: Grade A: Equipment room (such as fire-pump room,power distribution room, generator room, smoke control fan room, etc) door, fire?compartment, door on firewall; Grade B: Eclosed staircase, front door of stair room, smoke-proof?staircase and fire elevator share lobby door, front door of fire elevator, household door which directly opens to front room or shares room; Grade C: The vertical shaft door, such as strong electric wells, weak electric wells, pipe shaft door and air conditioning facilities. I hope this information can help you.

Q:Does anyone know fire-proof material of fireproof wooden door?: Fireproof wooden door goes through the flame treatment, so it can prevent fire. Its principle: Fire-retardant treated timber has become flame retardant material itself and its fire endurance has increased. The commonly used method of fire retardant treatment for timber including: Spraying method, soaking method, boiling method, vacuum method, vacuum-pressure method. Spraying method and soaking method are generally used for timber surfaces which are no longer going through planing process, and thin plate fire retardant treatment, whose thickness is less than 10mm .

Q:Are the specification of fireclay bricks and ordinary clay brick the same?: Do you want to know whether the specifications of fireclay bricks and ordinary clay brick are the same?

Q:How many kinds of refractory materials are there in the EI?: I suggest that you contribute articles to foreign SCI journals for the odds are better, and generally the articles that fill the bill will not be rejected. The traditional refractory materials can contribute to EI journal. If being rejected by EI journal, you can also contribute to Russia's journal Industrial Ceramics and Refractories. I didn't contribute to the Journal of Wuhan University of Science and Technology, the receiving cycle is almost 3 to 4 months. Though the impact factor is low, domestic EI journal is not so good, it is still SCI journal. This is my own experience, please take my advice. The best journals are the Journal of the American Ceramic Society and the Journal of the European Ceramic Society, I heard that they are not bad. But the best domestic EI refractory material journal is the Journal of The Chinese Ceramic Society. It is very long, but if it belongs to your university, it is another pair of shoes. Journals now all want to have materials about functional ceramics, and they don't want Chinese articles, if your English is not well enough, you can choose Ceramics International and Japan Ceramics but they have strict manuscripts reviewing standards.

Q:What are the construction fire-proof materials?: 1. fire?retardant?coating 2. fireproof?panel 3. fire proof and sealing material 4. flame resisting decorative materials 5. Green fire prevention materials

Q:How to choose refractory material: The crystalline refractory fiber mainly consists of polycrystalline mullite fiber, the optimum use temperature is 1300 DEG C, and the long-term use temperature of polycrystalline alumina fiber is 1400 DEG C. The service temperature of ordinary refractory fiber is 1150 degrees, and the use temperature of advanced refractory fibers (such as alumina, zirconia, refractory fiber) can reach 1700 degrees centigrade

Q:What material is refractory material?: Basic refractory materials, basic refractory, CaO, basic, MgO style alkaline earth oxide. The refractory materials mainly refers to magnesia refractories, dolomitic and lime refractory refractory. Main categories: (1) strongly basic magnesite brick, magnesia carbon brick, limestone and dolomite brick refractory materials;(2) alkalescent magnesia chrome refractories, forsterite refractory, magnalium and magnesia-chrome spinel refractory, basic refractory materials, high-temperature caustic slag, alkaline solvent resistance, strongly acidic slag flux or acidic refractory. The reaction is mainly used in steel furnace such as colour metal smelting furnace and cement kiln.

1. Manufacturer Overview
Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates
a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range