MET COKE SIZE 20-60MM

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Q: What is the density of coke?: The true density of coke: 1.8 ~ 1.95kg/cm3; apparent density: 0.8 ~ 1.08kg/cm3; pile density: 400 ~ 500kg/cm3

Q: What is the reasonable ratio of coal to coke: There are lignite, bituminous coal, anthracite, semi anthracite these categories. Under the condition of isolated air, the bituminous coal is heated to 950-1050 DEG C, and finally, the coke is made by drying, pyrolysis, melting, bonding, solidification and shrinkage.

Q: Ca3 (PO4) 2, SiO2, coke and other raw materials for the production of silica gel (SiO2? NH2O), phosphorus, phosphoric acid and CH3OH, the following process raw materials comprehensive utilizationCa3 (PO4) 2, SiO2, coke and other raw materials for the production of silica gel (SiO2? NH2O (P), phosphorus, phosphoric acid and CH3OH, the following process raw materials comprehensive utilization rate is high, less waste(1) in the reaction, which belongs to the replacement reaction is ______[optional: (I), (II) and (III), (IV), (V).(2) chemical reaction equation II under high temperature of ______; solid waste can be used for ______. CaSiO3(3) reaction to be carried out in isolation and oxygen under anhydrous conditions, the reason is ______.(4) CH3OH can be used as a fuel cell fuel in strong acid medium, the electrode reaction type anode for ______.(5) pointed out that the significance of ______. (VI) in this part of the industrial production(6) written by P H3PO4, the reaction of the ______ ______.: (1) according to the definition of replacement reaction, there are two kinds of compounds in the reaction of II, contains two kinds of compounds in the product, so it is not the replacement reaction of reactants, IV no elemental, so it is not a replacement reaction, V reaction is a chemical reaction, I and III reaction with replacement reaction conditions, so is the replacement reaction,

Q: The total amount of heat released by the fully burnt 200g coke is 60% by mass of 10kg water absorption [q coke =3.0 * 107J/kg, C water =4.2 * 103J/ (kg = C)], q:(1) how much heat is absorbed by water?(2) if the initial temperature of water is 10 degrees C, then, after absorbing heat, the temperature will rise to how much?: Dry water temperatures:Delta t=Q ceilingC water m water=3.6 x 106J4.2 x 103J/ (kg * c) * 10kgC = 85.7,At the end of a water temperature t=t0+ t=20 C +85.7 =105.7 oc,

Q: What is the difference between coking coal and coke: Coking coal is an essential raw material for the production of coking coal, coking coal is one of the main uses of coke, coke is full of coking coal, coking coal is necessary for coke.

Q: Who knows the proportion of pig iron and coke used in Cupola: Raw material inputs: the main raw material for casting pig iron, scrap steel, manganese, etc.. Under normal circumstances after the melting of ordinary cast iron scrap iron and scrap steel ratio of 9:1 or so, the drying enterprises use pig iron and scrap ratio of about 6:4, according to the requirements of the product. Because pig iron and scrap carbon content is not the same, the higher the carbon content of pig iron is about 4 ~ 4.3, low carbon steel scrap, about 0.8.

Q: How to distinguish the level of coke. What is metallurgical coke: The utility model is characterized in that the coal is formed by the compression of the coal powder, and a new type of coke, which is processed after carbonization, is called a coke. Metallurgical coke is coke, coke, iron alloy coke and non-ferrous metal smelting coke "

Q: What are the requirements for the quality of coke in blast furnace smelting: Different uses of different coke porosity index requirements, the general requirements of metallurgical coke porosity in the 40 ~ 45%, 35 ~ 40% in coke, coke export demand in about 30%.Coke crack degree and the porosity level, and the coking coal has a direct relationship, such as coal based coke refining, crack, high porosity, low strength; with coal as the foundation of the coal refining coke crack less, low porosity and high strength. The strength of coke is usually represented by two indices of crushing strength and abrasion resistance. Coke crushing strength refers to coke can resist foreign impact force without ability along cracks or defects at the broken, represented by the M40 value; wear strength of coke coke refers to the ability to resist external friction without surface of glass forming debris or powder, said M10. The cracking degree of coke affects the M40 value of its breaking strength, and the pore structure of coke affects the M10 value. There are many methods for determination of M40 and M10 value method, commonly used in our country the German migon drum test.

Q: How many degrees of coke ignition temperature can ignite coke: The average specific heat capacity is 0.808kj/ (KGK) (100 DEG C), 1.465kj/ (KGK) (1000 DEG C);The thermal conductivity is 2.64kj/ (MHK) (room temperature), 6.91kg/ (MHK) (900 DEG C);Ignition temperature (450-650) in air;

Q: What's the difference between coke and coke?: In the process of coal carbonization of coal material: when the temperature is higher than 100 degrees in coal water evaporation; the temperature rises to 200 degrees above, combined with the release of water in coal; up to 350 DEG C, caking coal begin to soften, and further the formation of colloid viscous (this phenomenon does not occur, peat lignite; etc.) to 400 ~ 500 degrees most of the gas and tar precipitation, called a thermal decomposition products; at 450 to 550 DEG C, the thermal decomposition continues, gradually thickening and curing the formation of residue char!

Send your message to us

*Email

*TEL

*Quantity

*Unit