Male Thread Brass Ball Valve in low price

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Material:Hot forged brass

Ball:Brass with nickle and chrome plated

Gasekt/Packing:PTFE

Nut:Stainless Steel

Handle:Iron

Size:1/2",3/4",1",1-1/4",1-1/2",2"

Thread:ISO228,BSP,NPT,ect

Temperature:-20℃≤T≤150℃

4.Pressure:P≤3.0MPa=30bar=435psi

Medium:water,oil,gas,ect

Material:Brass body,brass stem,brass ball,brass nut,Aluminium handle,Teflon seal

Q: Standard and specification for pressure test of valves: (11) when the valve with drive device is tested and its tightness is tested, the sealing test shall be carried out by using the driving device to close the valve. For manual drive units, seal test shall also be done with the actuating closing valve.(12) the by-pass valve installed on the main valve after the strength test and the sealing test. The strength and tightness test of the main valve is carried out. The main valve should be opened when the closing member is opened.(13) iron valve strength test, the application of Pratia tapping valve and valve cover, check whether there is any leakage.(14) the valve test, in addition to the provisions of the plug valve to allow sealing surface oiling, other valves are not allowed in the sealing surface of the oil test.(15) when the valve pressure test, the blind plate on the valve pressure should not be too large, so as to avoid deformation of the valve, affecting the test results (cast iron valve if pressed too tight, will be damaged).(16) after the valve test pressure, should promptly remove the water and clean the valve, should also be prepared for the test record.

Q: Can other valves be used instead of 10?: An elbow, an outer wire, screw down the joint of the hose, the elbow is joined together.

Q: What does the whole copper valve mean?: The whole valve is made of copper material. In addition to the ceramic core.

Q: Can the gas valves be switched off regularly?: The small valve called skin stopcocks, his design is often switch, but for the sake of safety, natural gas company also installed a lock valve in front, once the leak immediately close the valve, the valve once closed to find a Gas Co came to open, so it is not necessary the case don't go off.What we usually need to pay attention to is..:1, every time you finish cooking, you must close the pipe plug valve (the valve you said).2, regular inspection of the skin tube leakage (3 months 1 can be this).3, the leather pipe and the leather pipe plug valve connected to the place has a ferrule, inspection found loose, must be tightened with a screwdriver, in case of leakage.4, the use of gas should pay attention to indoor ventilation, winter must open lampblack machine, in case of poisoning.Don't worry as long as you do the above.

Q: What do you mean by "P54" in the valve z962y-p54 100V?: P54 is the body temperature, heavy rain or equal to 545 degrees, 100V is 10Mpa, that is 100 kilogramsThere are all the valves on the nameplate

Q: Air compressor out of the gas with what kind of valve control okay, globe valve or other?: What's the use of your air compressor? Is it manual or automatic? By the way, I think it's ok if the demand is not very strictWhat we used on board was the cut-off.

Q: What are the types of valves?: 1.1 classification by purpose and functionx09 (1) cut-off valve is mainly used to cut off or switch through the media flow, including gate valve, globe valve, diaphragm valve, ball valve, plug valve, butterfly valve, plunger valve, ball plug valve, needle type instrument valve, etc.x09 (2) control valve is mainly used to regulate the flow of medium, pressure, etc., including regulating valve, throttle valve, pressure reducing valve and so onx09 (3) check valves are used to prevent backflow of media. Check valves with various structures are includedx09 (4) diverter valves are used for separation, distribution, or mixing of media, including distribution valves and traps for various structuresx09 (5) safety valves are used to protect the medium against overpressure. Various types of safety valves are included1.2 classify by main parameters

Q: I would like to ask commonly used water valve what kind of? What are the characteristics?: Valve is used as cut-off media, the flow through the fully open, then the pressure medium to run minimal loss. Usually does not require frequent valve for opening and closing, and maintain the gate fully open or fully closed condition. Not suitable for use as a regulator or throttle. For high-speed flow of medium, the gate conditions can cause vibration of the gate in the partial opening, and the vibration may damage gate and valve seat sealing surface, and the throttle gate will suffer erosion media. From the structural form, the main difference is that the sealing elements form. According to the form of seals, often divided into several different types of valve, such as: wedge gate valves parallel gate valve, parallel gate valve, wedge gate valve. The most commonly used form of wedge gate valve and parallel valve

Q: What do the D373W and D373H of the valve mean?: Upstairs said yes, I have factory production, this butterfly valve.

Q: How are the types of valves classified?: Pneumatic and hydraulic valvesPneumatic valve and hydraulic pressure based on a certain air, water or oil as the power source, using the cylinder (or cylinder) and the movement of the piston to drive the valve, the general pneumatic air pressure is less than 0.8MPa, the hydraulic or hydraulic pressure is 2.5MPa~25MPa. Such as used to drive diaphragm valves; rotary gas and liquid drives are used to drive ball valves, butterfly valves, or plug valves. The driving force of the hydraulic device is large, and it is suitable for driving large diameter valves. If used for driving plug valves, ball valves and butterfly valves, the reciprocating motion of the piston must be turned into a rotary motion.

Send your message to us

*Email

*TEL

*Quantity

*Unit