Hydraulic hose fittings for 2SN DN16

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Material: Carbon steel, alloy steel, stainless steel, aluminum alloy and brass.

JIC, SAE, DIN, BSP, JIS and ISO standards

Products:high pressure hose, pipe and tube fittings, flange adapters, straight fittings, tee fittings, cross fittings and various adapters

Q: Is hot melt hose toxic and harmful?: The heater adopts the U.S. and high temperature heating wire line, uniformly wound around the pipe wall, with thermal insulating properties and uniformity, good heat resistance, heat insulation material of high quality, ensure that the insulation performance of larynx.

Q: The newly purchased natural rubber tube is too large. How can it be removed?: The activated carbon is divided into 8 parts, put in the dish, the dumbbell rubber smell removed - prepare 400 grams of ash, used to be among them after washbasin packing box of formaldehyde, because some of the harmful substances is colorless and tasteless, more clean, more secure. In the bubble tea, put in the refrigerator can achieve the deodorization effect. If you do not have tea, you can also cut lemon or willow, and only half a small piece will be effective. Smoke in room. The soaked waste tea leaves dried, placed in the corner of the room, using the principle of physical adsorption of tea to remove dumbbells, rubber flavor. You can also use a towel dipped in diluted vinegar, go to the dumbbell rubber flavor.

Q: How can the rubber joint be classified according to the range of temperature?: A universal rubber flexible joint is suitable for use in water from -15 DEG C to 80 DEG C or in a variety of acid and alkaline solutions with concentrations below 10%.

Q: What is a rubber core pulling method?: The hose shall be filled with water or gas at a pressure of 0.5 0.8N / mm before pouring concrete. At this point, the hose diameter can be increased by about 3mm. When pouring concrete, the vibrating bar should not touch the hose, and should check the pressure of the water meter regularly. If there is any change, the pressure must be filled.Smoke tube longer than tube core pulling slightly later. Before the pipe is pumped, the water is lowered and the pipe section is reduced, and the pipe can be drawn away from the concrete. The order of pumping is usually first, then first, then first, then straight.

Q: Method for inserting glass tube into rubber tube when assembling instrument: Pipe connection is widely used in the laboratory. Besides the sleeve of the glass tube, there are plastic tube, rubber hose and iron pipe sleeve, etc. the sleeve connection method can be carried out by referring to the sleeve connection method of the glass tube.

Q: The principle of the common bicycle valve: The main body of the valve core is a small upper end hollow and solid cylinder at the lower end, and a small hole is opened at the lower end of the lower end to connect with the hollow part.

Q: How do the automobile rubber hoses combine with the quick couplings?: Turn the rotary handle on the quick connector to the open position first;

Q: What are the materials used in rubber joints? What are their advantages?: Material has ordinary natural rubber, three yuan ethylene propylene (EPDM), nitrile and so onTo choose a different material, it depends on what kind of medium to go

Q: Hydraulic quick change joint (external thread) how to connect and seal with hose? Do you need a transition joint?: As for hydraulic joints, they don't need other aprons to seal them, and the product itself is concave, and it is convex at one end, so it can be completely sealed after connecting.

Q: How can the rubber tube be used properly and how to use it properly?: The hose burst caused by frequent and severe pressure impact. This situation is not generally under the static pressure caused by too much, but the number and intensity and pressure impact. Engineering machinery in operation, will be repeated in the hydraulic tubing suddenly increased or decreased, which impact on the oil pressure of frequent the damage of the oil seal, resulting in increased, loosening hose leakage and rupture foaming and pipe joint. Therefore, in operation, the valve stem can not be too hard, must be gentle.

Send your message to us

*Email

*TEL

*Quantity

*Unit