Hot Sale Construction Aluminum Alloy Template System

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Product Details

Economic traits	Frequent recycling and low averaging cost
	High recovery rate and residual value
	High efficiency of construction,short construction period
	No crane,less labor cost(30% of timber and steel formwork)
Quality	Good construction effects & quality; No troweling
	Wide scope of application and strong bearing capacity
	High stiffness and light weight
Environmental Protection	Safe construction and no construction waste
	Ecological and clean production
	Popularization and promotion; Benefit the society

Design	International Design Team
	Advanced Design Platform
	Open-minded Design Concept
Service	Professional Installation Group
	Committed Service,Source of Development
	Stay Close to The Customers and Provide Speedy Services

Characteristics of SNTO Aluminum Formwork

Economic traits	Frequent recycling and low averaging cost
	High recovery rate and residual value
	High efficiency of construction,short construction period
	No crane,less labor cost(30% of timber and steel formwork)
Quality	Good construction effects & quality; No troweling
	Wide scope of application and strong bearing capacity
	High stiffness and light weight
Environmental Protection	Safe construction and no construction waste
	Ecological and clean production
	Popularization and promotion; Benefit the society

Design	International Design Team
	Advanced Design Platform
	Open-minded Design Concept
Service	Professional Installation Group
	Committed Service,Source of Development
	Stay Close to The Customers and Provide Speedy Services

Q: Cast aluminum plate how to deal with a small hole: Aluminum welding, you are there is a stomatal, welding process is not handled well. Strength certainly not reach, not to mention performance. There is no picture, look at the defect situation, I see can not remedy, think of ways to achieve its initial use of performance. Cast iron are recognized as difficult to weld it, this is a large cast iron machine arm after the fracture of the arm, the use of the scene, the accuracy of performance did not damage

Q: I stood a piece of the shop when the remaining aluminum-plastic plate plate, this aluminum layer even so, is auspicious brand, this is the situation, I do the store will fall off: All over the name of this brand is the name of the aluminum-plastic plate.

Q: OKorder side there is no production of new materials, aluminum-plastic plate manufacturers? I want to use the pillars, the need to process the arc, very anxious to solve!: I am not in OKorder in Kunming, do not know useful to you! The last time I do in Liupanshui do gas station is also need to pack pillars, Party is also required to use new materials, aluminum-plastic plate, I find a long time did not find, and later from Kunming cloud like building materials, anyway, OKorder is not here from us Far, useful words remember to adopt! Thank you

Q: I would like to open an aluminum-plastic plate of the store, who knows Zhejiang side there is no SHJIX OKorder auspicious manufacturers?: Want to open the aluminum plate store this idea, not enough, after all, is a store, often confined to a manufacturer of the brand.

Q: What are the folds of aluminum: Aluminum-plastic composite board slot can generally open V-groove, U-slot, etc., several typical slotted as shown in Figure 1. Aluminum-plastic composite panel plate in the cutting board to take into account the size of the fold , Generally add about 25mm on each side. Cut the composite board needs four sides of the planing slot, that is cut to a certain width of the inner layer of aluminum and plastic layer, slot depth must be strictly controlled in the front aluminum plate at least 0.3mm thick plastic core To ensure that the aluminum-plastic composite panels have sufficient toughness to prevent the fold at the aluminum skin fracture, and then folded into a 90 ° angle, so the board surface weight and curtain wall at any time will be positive and negative wind load pressure by the four sides 0.5mm aluminum plate to bear, therefore, slotting is the aluminum-plastic composite panel panel of the weakest link, but also under the wind load under the first destruction of the site

Q: How to install the aluminum-plastic panel ceiling?: The more common installation method is to directly through the self-tapping screws in the aluminum plate above the keel, so there will be nail caps, but can be secretly fight. This is relatively easy.

Q: Will the aluminum plate and aluminum plate and plastic plate what is the difference ah?: Aluminum plate with aluminum buckle plate is the best one is a long one is a plastic one is the price of aluminum alloy is not necessarily see where the aluminum plate in OKorder, there are more than 100 are also dozens of fast also Buckle on the thousands of aluminum plate also if the above lights bad bad repair Kouban better, then he can be a piece of demolition

Q: White aluminum plate can be a new brush color? Store white aluminum-plastic board for a long time dirty, you can buy a new paint back to brush it?: Aluminum-plastic plate is divided into inner wall panels, external wall panels, wood plate, Gang plate, fire board five categories, a total of hundreds of different specifications of different colors of the plate;

Q: Aluminum-plastic board to install a seamless splicing or leave a gap: Stay good looking

Q: Silver aluminum plate is what material is not silver aluminum plate?: According to the current building facade commonly used materials to judge, it should be said that aluminum is a class, either aluminum or plastic plate, or according to the pronunciation, it should be said that there may be aluminum veneer. There is something close to carbon.

Send your message to us

*Email

*TEL

*Quantity

*Unit