Q: What is the principle of using gas in argon arc welding machine fast?

First of all, your gas cylinder does not change too much. Whether the gas discharge welding machine controls or not depends on the size of the gas bottle. When welding, the argon gas transmission does not need to be too large, and a little bit of air will do;Check each section of the trachea is broken, the general welding torch of the two joints, as well as the middle often bent, or often foot of the place, easy to break, leak;If there is a delay gas switch, to extend the air. Had a little effect on the air.There's nothing else to look for!!!

Q: There are several kinds of arc welding machine, argon arc welding machine and several kinds. What are their occupational hazards?

Manual arc weldingArgon tungsten arc weldingCarbon dioxide gas shielded arc weldingsubmerged arc weldingmetal inert-gas welding

Q: What do you mean by "ground arc" of argon arc welding machine? Is it because it doesn't arc or is it connected directly to the ground to prevent electric shock?

Some of the ground wires come from the positive electrode, some from the negative electrode, and the electrodes are marked or referenced. The electrodes are directly connected to the welded metal objects before welding.

Q: How to use the arc welding machine?

Aluminum can focus on argon arc welding argon arc welding of Odin Wei, Wei Odin have special customer service and debugging

Q: Argon arc welding machine general how much money? Which brand is better?.

Wuxi Han God, Wuxi Fenghua, buy about 800 on it.

Q: What's wrong with argon arc welding machines without high voltage output?

You look at the two 510K high pressure discharge nozzle side there is no problem or breakdown. Just look at the tube next to it.

Q: I wonder what the formula for calculating the power of electric welding is. There are several gears in the two output, and my calculations seem to be out of order. I think my calculation is wrong. I would like to ask you a complete calculation method of welding power

It depends on what type of welding machine, how much current welding, and the length of the welding cable to estimate:1. Commonly known as: AC arc welding arc welding transformer, mainly BX1-500, BX3-500 to 300A; if the current welding, the power consumption per hour is about 8.4 degrees (according to the welding efficiency of 80%, the utilization rate of 70%, the welding voltage 32V calculation);2. SCR rectifier welding: ZX5-500; if the current is welded by 300A, its power consumption per hour is about 8.96 degrees (press welding efficiency 75%, utilization rate 70%, welding voltage 32V calculation);3. Inverter welding machine: ZX7-500: if the current is welded by 300A, the power consumption is about 7.47 degrees per hour (90% of the welder efficiency, 70% of the use rate, and 32V of the welding voltage);The above calculations assume that the length of the welded cable is 0 meters, and the actual power consumption will be greater because of the loss of the welding cable.

Q: I would like to ask the next ZX7-400 inverter DC welder quite a number of watts of power, thank you

ZX7 1 400: invert DC hand arc welding machine:1. rated output current: 400A2. rated output voltage: 36V3. rated output power: 14.4KW4. rated input power: about 18KWTherefore, the ZX7 400 welder continuously uses the power consumption of about 18 degrees per hour at the maximum output power;Of course, in actual use it is impossible to do welding work continuously or will not always use maximum output current welding, so it is actually smaller than this value;

Q: Excuse me: reallink argon arc welding field effect transistor K2698 can use IRFP460 substitution?

K2837 substitution is recommended.

Q: Can argon arc welding machine be used as cutting machine?

May not。Argon arc welding can not be used as plasma cutting machine. It is also impossible to weld the parent metal with tungsten.