E.S Electronic Optical Edge Finder

Ref Price:

Loading Port:: China Main Port

Payment Terms:: TT or LC

Min Order Qty:: 30 Pieces pc

Supply Capability:: 3500 Pieces per Month pc/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

Detailed Product Description

1.Touch point LED indication

2.Manufactured from high quality alloy steel

3.Hardened and precision ground

4.Accuracy:0.01mm

ES electronic edge finder with led and beep, apply to conductive workpiece

and machine tool

At present,we have 3 kinds of E.S Optical Edge Finder,the size as below,

Order No.	Diameter of Holding Bar	Length	Accuracy
0927.007	20	164	0.01
0927.008	32
0927.009	20	98

Order No.

Diameter of Holding Bar

Length

Accuracy

0927.007

164

0.01

0927.008

0927.009

Q: How can the reaming of stainless steel extend the life of the reamer and allow Kong Guangliang to help with various problems?: Cooling and cooling are needed during processing. Coolant and lubricating fluid are needed

Q: Please enlighten brother snow reamer 150125110 motorcycle valve is not universal and how the hinge valve: Motorcycle valve reamer is a set of the above several cars can be common.Reaming the valve is the best way to find a local repair car or motorcycle master, which is not clear here.Generally use 75 degrees, then 15 degrees and 45 degrees of reamer, and finally the effect after reaming, and then use several tools to trim. Use 45 degrees to the right contact width of reamer, reamer can take 15 degrees contact hinge low 75 degree knife to contact surface to improve the contact surface, preferably 1 mm or so, if it is too wide for 15 degrees and 75 degrees of cutting narrow. After reaming, grind the valve and check the seal.

Q: Four what are the advantages of titanium blade reamer: After TIN plating, the blade life is prolonged, and secondly, the machining ability is improved. If the titanium plating, then do not use cutting fluid. Cost saving.

Q: Usage of valve reamers for motorcyclesCG150 CG125 bedroom, 110, reaming of motorcycle valve reamers?And the order after which the reamer is used?: The first tip (reamer reamer, minimum angle less than 45 degrees) winch valve seat airway first incline and then switch the sharpness of the medium (reamer, medium angle equal to 45 degrees) of the reamer winch valve seat sealing surface, the maximum angle of reamer reamer, the angle (more than 45 degree) winch cylinder valve excessive arc, 3 steps are not interchangeable and wrong, the center must guide rod and valve reamer circle concentric, 3 plane hinge width to be the same, after the winch with valve and valve grinding sand milling grinding can be completed!

Q: Use and do not use the threaded hole reamer reamer, what do you mean, how to choose the aperture: Because the drill hole drilling accuracy is not high, the hole is rough, and the internal hole accuracy requirements are relatively high, reaming can improve the accuracy of the hole and the surface roughness of the hole.When machining threads, the drilling diameter is approximately the nominal diameter of the thread minus the pitch of the thread.

Q: With a machining center, the diameter of the hole is 28, and the cutting amount of the reamer when reaming: According to what you said, what you said was boring. How did you say it was twisted?I said one of my experiences: if boring, the speed is about 500. Feed 70.If the speed is 60, when feeding 40, if you want the correct tolerance, add lubricating oil. Minus tolerance plus cutting fluid, with kerosene, too.

Q: What drill and reamer are used to process an empty diameter of 8mmH7?: You can refer to the relevant mechanical processing manual, should have an introduction, I think it should be 7.8 of the drill, 8 of the reamer

Q: The edge of the reamer and drill bit can cut metal, one is only oriented, and why?: The edges of the two cutters can be used for micro cutting and scraping the walls of the extruded holes. The main cutting edges are end teeth (ends), but the main cutting edge of the reamer is small, the force is uniform, and the vibration is small. The drill main cutting edge cutting capacity, the cutting force is high, at the same time by centering the drill chisel edge effect, if the chisel edge center of bad point circle, the pore radius, the edge was just a guide.

Q: How do you choose the tolerance of reaming when reaming?: The processed reamer size with many factors, such as what the coolant, cutter speed, feed rate, exit reamer also pay attention to.The standard reamer is generally the axis system size. Such as H8, H7, H6. Of course, also can according to the hole size to build special dimensions and tolerances of the reamer.The theory of pore size is negative to wring size zero. But the actual wring hole must be more than theory. General tolerance of hole is smaller, the precision is higher.The general processing speed is slower, the cooling liquid, fully feed more quickly, the size of the hole is out of tolerance near.High strength high speed steel and hard alloy can be used as tool materials when reaming high strength steel and ultra high strength steel. High speed, high cobalt, cobalt or aluminium containing high speed steel in high performance high speed steel is very suitable for processing this kind of steel. For example, a reamer made of cobalt carbide super high speed steel W12Mo5Cr4V3Co5Si is 18mm in diameter,When reaming high strength steel (b=1200 to 1300MPa), each reamer can be reamed with 60~70 holes. When the hinge is n=140r / min, f=0.05mm / R, the roughness is Ra, 1.6gm.Carbide reamers for high strength steel, shown in Figure 4-4, are made of YT15 carbide. The reamer for L/D is less than or equal to 5 and D=6 to 80mm hole. Full use of emulsion when in use. If a drill bush is used, the rotary drill sleeve must be used to avoid the friction between the hinge blade and the drill sleeve. When the operation, the first contact with the workpiece after the tool and then drive, the best time to stop the car when the knife is returned.

Q: Why reaming with reamer is the workpiece of ductile iron 500, the aperture will be smaller, and the aperture requirement is 9. After reaming, the reamer will not enter the hole. What is the reason why the hole is too small for the reamer to go in?: You first look at the surface of the processing hole is black and shiny, and if so, the following three cases are more likely:1. the reamer is blunt, or the reamer is too wide.2. reaming allowance is too large.3. reaming too fast.

We developed small high-precision CNC lathes based on the imported technology, with high-quality accessories and universal electric control systems. Our machine tools are mainly used in aviation, automobiles, electron, clocks, optical instruments, moulds, computers, medical equipment and so on. At present, these machine tools are enjoying a good reputation among our customers. Accessories and tools are the basic of high-quality precision machinery.

1. Manufacturer Overview

Location	Shaanxi,China
Year Established	2010
Annual Output Value	Below US$1 Million
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability

a) Trade Capacity
Nearest Port
Export Percentage	1% - 10%
No.of Employees in Trade Department
Language Spoken:
b) Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range