Dehumidifier for Indoor Swimming Pool

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Model		KP-30	KP-40
dehumidification at 30ºC - 80% R.H.	liter/hr	2.9	4.3
heat recovered	kW	3.8	5.6
circulating air flow	m³/h	600	800
power supply (at 30ºC - 80% R.H.)	W	750	1110
electrical heater optional	kW	2	2
power supply	V/Hz/P	230/50/1	230/50/1
refrigerant		R410a	R410a
compressor		toshiba
sould level at 1 meter	dB(A)	44	46
selection for max. area of indoor pool	m²	56	83
selection for storage area		50 ~ 100	100 ~ 150
installation place		floor-standing or wall-mounted
unit size (L * W * H)		1300x200x800	1500x200x800
net weight		65	80
relative humidity range	% RH	40~100
room air temperature range	ºC	10~36
condensate drain, pipe size	mm	16

FAQ
Q 1.Okorder Quality Control?
We hold a very strict quality control system to check every connector of our products for

your safety.

Q 2: How do you care for your kitchen appliances?
A: Keep good Ventilation indoor. Open the doors of the kitchen appliances, if not. There

will be some mildew on cutting board and other kitchenware, because the water vapor can not

evaporate easily.
Keep clean of all the appliances. Each kitchen has its special cleaning fluid，please go to

Kitchen cleaning stores buy some clean them on time.

Q 3: Which one do you use the most of kitchen appliances?
A: Assuming you mean small appliances .I say too many! At one time we would buy every one

that came along; including a hot dog machine, pizza maker, elec. carving knife, elec.,

toaster oven,. Most have been garaged sale (sold) or are stored in the garage. Most used;

coffee maker, microwave, blender and mini food processor. OK?

Q: What is the principle of a spray dehumidifier?: When the temperature of the wet gas drops below the dew point, the steam condenses and reduces the humidity of the gas

Q: When the automobile air conditioner is used, why is the dryer hot?: The dryer is mounted behind the condenser and the compressor compresses refrigerant to produce a high temperature, high pressure gas into the condenser. A semi fogging refrigerant, which is cooled by a condenser to about 70 degrees, enters the dryer. So the dryer is very hot and hot

Q: What are the common breakdowns in the automotive dryer?: After 50 thousand km or one and a half years, observe if there is water in the storage tank. If there is water, replace the desiccant. (2) if there is a leak phenomenon, the automobile air pressure can not go up, and then repair by air leakage

Q: What is the cause of the dryer blockage?: The refrigeration system is not cleaned before assembly and welding.

Q: What are the factors affecting the dryer?: The dry hot air transfers heat to the particles in the drying silo, removes moisture from the surface of the particles, and then sends moisture back into the dryer. Therefore, there must be enough air flow to heat the resin to the drying temperature and maintain the temperature for a certain period of time.

Q: How to install the car air dryer?: Installation location: away from the heat radiation source, well ventilated, close to the gas road system, the first use of gas tank, drying tank top should leave 30 ~ 50mm space, in order to replace desiccant

Q: What is the principle of a hydrogen dryer?: Adsorption at a high temperature and partial pressure of water vapor at a high temperature and low water vapor partial pressure (regeneration)

Q: How do I choose the dryer?: The characteristics of materials and products, such as material form

Q: What is the difference between the air dehumidifier and air dryer?: You should use an air dryer and add a steam separator and filter

Q: What are the clogging problems in dryer?: Chill, condensation, or frosting for dry filtration, resulting in insufficient refrigerant supply to the evaporator or cause refrigerant to not cycle refrigeration

Send your message to us

*Email

*TEL

*Quantity

*Unit