CSR60 MET COKE

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Our companybegan to export coke when China cancelled 40% of coke export tariffs and quotason January 1, 2013.

We can offer belowgrade met coke, origin from China.

Q: Coke can be used to do what carbon black can be used to do?: Carbon black in plastics industry is the first use of carbon black pigment coloring, is cheap. Second carbon black in plastics industry use is to have good ultraviolet absorption effect, its application shows quite obvious protective effects in plastic. Third carbon black in plastics industry use is conductive.

Q: Coke is how to produce, what is its purpose?: Under the condition of air isolation, the bituminous coal is heated to 950-1050 DEG C, which is finally made into coke by drying, pyrolysis, melting, bonding, solidification and shrinkage. Coke oven gas produced in the process of coking and recovery is not only a high calorific value of fuel, but also an important industrial raw material for organic synthesis.

Q: Effect of coal fineness on coke: In coking, the caking property is not good and the coke quality is reduced. Therefore, from the perspective of the uniformity of coal, coal fineness of some good. From the operation point of view, the greater the fineness of coal coal bulk density is lower, the production capacity of coke oven is low, into the coke oven, fine coal powder easily by gas is brought out, and easy blockage of ascending pipe, gas collector, affect the normal production of the coke oven, and the set of tar in the trachea increased, the effect of recovery operation. Therefore, from the production point of view, the fineness of coal should not be too large. Bulk coal in the top of the coke oven, coal crushing fineness of the general control in less than 3mm component in the range of 73~83%. Tamping coking, generally about 90%. In this range, the fineness of pulverized coal can meet the requirements of coke quality and coke oven operation. The small coal crushing will reduce the adhesion and the bulk density of coal, so as to reduce the coke quality.

Q: What is the difference between coking coal and coke: Coking coal is the raw material for producing cokeCoking coal is produced by carbonization: coal gas (carbon monoxide), coal tar, coke

Q: Who knows the proportion of pig iron and coke used in Cupola: There are doubts: if the scrap ratio is too large to increase the difficulty of processing, product quality can not be guaranteed. The proportion is too high or too low are abnormal.2, auxiliary material input: foundry auxiliary materials mainly coke. Ordinary casting (except dry cylinder) 1 tons ~ ~ 5 tons cupola, each investment of 1 tons of coke, according to the situation of the piece can be from 4.5 tons to 5.5 tons. Ordinary blank (special pieces extra), 5 tons to 10 tons per 1 tons of coke in cupola furnace about 6.5 tons to 7.5 tons of blank (waste products re melted are calculated according to the above method).

Q: What is the amount of waste gas produced by a ton of coke burning: Process for producing coke, coke oven gas and coking chemical products by thermal decomposition and coking.

Q: Can the sulfur content of coke affect the casting process of nodular cast iron at 0.65?: The high sulfur content of nodular cast iron, the most significant impact on the casting is caused by poor balling,

Q: What is the difference between coke and semi coke in ferrosilicon smelting process? In the process of energy statistics in the end should be 0.9714 of the conversion coefficient should be used with the conversion coefficient of 0.75 x 0.9714, please expert advice? emergencyUrgent!: Coke is used for smelting iron alloy coke, and the coke is used in blast furnace and used for copper, lead, zinc, titanium, antimony, mercury and other non-ferrous metal smelting of blast furnace, reducing agent, heating agent and columnar skeleton.

Q: Coke in the whole process of steelmaking in the end is what to do, just to provide heat or carbon and other substances into steel or iron?In the study of coal classification inside, one is divided into coking coal, coking coal and coke as main, and then you see is steel or iron coke must material. What is not clear. In the end, out of coal mining is mainly used to burn energy extraction, or said that coal like oil can be converted into other products, which is a coke can convert?: It is necessary to add coke, pellet, sinter ore, ore and other materials into the blast furnace in a certain proportion, batch and sequence, and then to produce molten iron in the reducing atmosphere of the blast furnaceAfter the hot metal to steel in converter against the general converter, scrap also need to add a certain amount of used to balance the heat. Hot metal and scrap are added to the converter after the oxygen lance for oxygen operation, the oxidation of oxygen to carbon in liquid iron, silicon, manganese, phosphorus, sulfur and some non-metallic inclusions to form steel. Adding lime, dolomite, iron oxide and mine slag and coolant is needed in oxygen at the same time. After the completion of steel smelting in the tapping process according to different requirements with the corresponding iron alloy steel, after also refining process.

Q: What are the quality indicators of coke: More than 83 of the fixed carbon; sulfur below the volatile content of less than 1.5; ash around 15 e:Mechanism coke: used in metallurgy; steel plantFiddle coke size 8cm-150cm: of molten iron for casting {;} of motor shell, radiator, mechanical counterweightCoal tar: molten iron; used in the casting of motor shell, radiator, mechanical counterweightLarge modified coke: {for ordinary casting; mechanical parts such as rough parts for 2-3.5 tons of furnace type}The shape of coke size 25cm:{is used for ordinary casting and slightly rigid casting products, such as water pump pipe fittings, such as fire fastener

Send your message to us

*Email

*TEL

*Quantity

*Unit