Corrugated Water Suction Hose--Wire Reinforced Hose

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Corrugated Water Suction Hose--Wire Reinforced Hose

Rubber dredge suction hose:
1.SBR&EPDM
2 Large supply ability
3.Excellent in anti-abrasion

4. Excellent in anti-abrasion
5 Best quality
6 Fast delivery

7 easy to install

8. Tube: Black abrasion resistant Natural Rubber

9. Reinforcement: Multiple plies of polyester fabric witha spring steel helix wire.

Q: SolidWorks how do you put rubber hose on the iron pipe?: It is important to note that different materials are assigned to each other: metal and rubber. To produce engineering drawings that guide production, fill in the corresponding section lines on the cutaway surface.

Q: What is a rubber core pulling method?: For short component hole, a hose can be used to bend through two parallel holes; if it is used for retaining hole of long component, the two hoses of anchor can be connected by iron sheet sleeve. The length of the bushing should be 400 - 500mm, and the inside diameter should be 2 - 3mm larger than the outer diameter of the hose. The fixed position of steel derrick hose available, spaced not more than 0.5m, and fasten with steel skeleton.

Q: The engine cylinder head cover behind the drop rubber tube what reason (Xichai 490 engine) (note the valve chamber cover tube): The valve chamber of the engine cylinder head cover counterclockwise with 8~10 open wrench counterclockwise unscrew rocker screw. Place the piston at the top dead center, turn the rocker head wire clockwise until the hand can not be moved, then back half a circle, then lock the nut.

Q: My company does high-quality rubber tube, all of the core method, and why use EPDM to do the inner tube, it is difficult to take off the core, please point out! What's the reason?: The core needs to be removed, and if it is too long, the mandrel can be divided into two sections and separated from the 2 sides

Q: The principle of the common bicycle valve: The diode is powered by single items. The bicycle valve is single - ventilated. Basically, a rubber is wrapped over the valve coreThe rubber is wrapped in the long, thin hole under it

Q: Difference between non-standard rubber joint and national standard rubber joint: Non standard is in shape and about the structure of standard atlas case material of flange thickness, flange ring thickness, diameter and thickness that relax the requirements, strictly speaking, these are unqualified products, of course, a certain extent to relax the standard does not affect the use, but too much to the influence of the relaxation of standards to use performance.

Q: What are the properties of an oil resistant rubber hose?: The early detection of the hose can effectively prevent the hose from the quality problems caused by security risks, the people's production and life plays a necessary role in supervision and protection. One-stop provides the physical and chemical properties of product materials, reliability testing, safety assessment and component analysis, to achieve a full range of testing and protection, is an important basis for ensuring product operation!

Q: What is negative pressure rubber shock proof joint? Is vacuum piping available?: With high pressure, good elasticity, large displacement, balance pipe deviation, absorbing vibration and noise reduction effect, convenient installation, but also can greatly reduce the noise and vibration of the pipeline system, which can solve all kinds of line interface displacement fundamentally, axial expansion and concentricity problems, mainly installed in the pump inlet the vacuum pump inlet, or large, can solve the 100% rubber joint suction flat phenomenon.

Q: Single ball chloroprene rubber flexible joint, Shanghai Song Jiang rubber ball joint manufacturer where?: Rubber joint is also called soft rubber pipe joint, flexible rubber joint, soft rubber joints, rubber joints, high-pressure rubber joints, rubber shock absorber, compensator.

Q: Excuse me, how can I get waterproof wires in the water?: You can find a little longer than the water into the rubber tube, the wire will be worn, the rubber tube fixed, so that the water is only rubber hose. After a period of time, check that the hose is leaking so that it can be kept dry for a long time.

Send your message to us

*Email

*TEL

*Quantity

*Unit