Coke Breeze of 0-10mm
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 m.t.
- Supply Capability:
- 100000 m.t./month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Structure of Metallurgical Coke of Coke Breeze of 0-10mm Description：
Coke is made by high temperature metallurgical coke for blast furnace smelting, casting and gasification. Occurring in the process of coking after recovery and purification of coke oven gas is a high calorific value of fuel, is an important industrial raw material in organic synthesis.
If foundry coke, general demand big granularity, low porosity, high fixed carbon and sulfur content is low;Chemical gasification with coke, lax to strength requirement, but it requires good reactivity, high ash melting point;Calcium carbide production with focal requirements to improve the fixed carbon content as much as possible.
2. Main Features of the Metallurgical Coke of Coke Breeze of 0-10mm ：
• Quality assurance
• Mutual benefit
• Preferential price
• Various choice
3. Metallurgical Coke of Coke Breeze of 0-10mm Images:
4. Metallurgical Coke of Coke Breeze of 0-10mm Specification:
Parameters | Guarantee | Rejection |
Total Moisture (As received basis) | 5% max | |
Ash (dry basis) | 12.5% max | > 13.5% |
Volatile Matter (dry basis) | 1.5% max | > 1.8% |
Sulphur (dry basis) | 0.65% max | > 0.75% |
Phosphorus (dry basis) | 0.035% max | > 0.045% |
M10 | 7% max | > 9% |
M40 | 84% min | ＜82% |
CSR | 64% min | ＜62% |
CRI | 26% max | > 28% |
Size 30-90 mm | 90% min | |
+90 mm | 5% max | > 8% |
-30mm | 5% max | > 8% |
5. FAQ
What are coke's main physical properties?
on the relative density of density, coke, coke porosity, thermal conductivity for the heat capacity of coke, coke, coke, coke ignition temperature, coke thermal expansion coefficient of thermal stress and coke, coke shrinkage rate, coke resistivity permeability, etc.
The average heat capacity is 0.808 kj/(KGK) (100 ℃), 1.465 kj/(KGK) (1000 ℃)
Thermal conductivity is 2.64 kj/(MHK) (room temperature), 6.91 kj/(MHK) (900 ℃);
Ignition temperature (air) is 450-650 ℃.
- Q:What is the sample quantity of coke moisture test? What is the test time? How many degrees? That is the national standard.
- Test procedureDetermination of total moistureA, said the samples size less than 13mm with pre dried and weighed for about 500g (referred to 1g), smooth specimen,B, a sample tray is placed on the 170 a 180 C in the drying box, LH removed after cooling, weighing 5min. C, check dryness, each time 10min, until the two consecutive quality difference in LG, calculate the quality of the last time.Determination of moisture content of samplesA, with the weighing bottle drying to constant quality in advance and has quickly called weighing samples size less than 0.2mm uniform mixing of the 1 + 0.05g (referred to 0.0002g), flat on the weighing bottle.B, will be filled with a sample of the bottle to be placed in the 105-110 drying box drying 1H, remove the weighing bottle immediately covered with lid, put into the dryer to cool to room temperature (about 20min), weighing.C, check of dry, insult 15min, until two consecutive poor quality in 0.001g, take the quality of the last calculation, if quality is weight gain first calculated on the basis of.Five, the calculation of test resultsCalculation of total moisture content according to formula (L):
- Q:I see that there are metallurgical coke and coke on the Internet, what is the difference between them (I hope to be able to say in detail) and a level of two points, how is this going on?.. Where is the quality of coke in China? Hunan good coke plant which? Although the problem is a little bit more, I hope that insiders can give some useful information. Extremely grateful.
- Coke is a special and molten iron cupola coke. Coke is the main fuel cupola molten iron. Its role is to melt the burden and make the hot metal overheating, the support column to maintain good ventilation. Therefore, the foundry coke should have large blocks, low reactivity, porosity is small, with impact crushing strength, low ash and sulfur enough
- Q:What is the difference between coking coal and coke
- Therefore, coke is not coking coal, coking coal is one of the products after processing
- Q:How much coke can a ton of coal
- The key depends on volatile coking coal quality good volatile low words should now 1.3-1.4 tons of coking coal out of a ton of coke
- Q:What is the use of petroleum coke
- Petroleum coke, petroleum coke. Solid residues produced by high temperature coking of residual oil, residual oil or bitumen from petroleum refining.
- Q:What are the requirements for the quality of coke in blast furnace smelting
- 4, volatile in coke: according to the volatile content of coke can determine the maturity of coke. Such as volatile content is greater than 1.5%, is said to produce coke; volatile less than 0.5 - 0.7%, it is said to be overdone, the general maturity of metallurgical coke volatile is divided into about 1%.5, the moisture in the coke: water fluctuations will make the measurement of coke is not allowed, resulting in fluctuations in furnace conditions. In addition, the increase in the moisture content of Coke will make the M04 high, M10 is low, the drum index error.6, the screening of coke composition: in the blast furnace coke particle size is also very important. In the past, the particle size of coke in our country is as follows: the coke size of large coke oven (1300 - 2000 square meters) is greater than 40 mm; the coke size of medium and small blast furnace is larger than 25 mm. However, some of the steel test shows that the coke particle size of 40 - 25 mm as well. Larger than 80 mm of coke to be whole, so that the particle size range. The coke block is uniform, the gap is large, the resistance is small, and the furnace condition runs well.
- Q:The sulfur content of coal and coke in general, the coking process of sulfur content of coal into the output of sulfur content of coke compared to those who are high and low?
- Of course, the sulfur content of coke is low. Coke quality requirements: two grade coke containing sulfur below 0.7%
- Q:Coke in the whole process of steelmaking in the end is what to do, just to provide heat or carbon and other substances into steel or iron?In the study of coal classification inside, one is divided into coking coal, coking coal and coke as main, and then you see is steel or iron coke must material. What is not clear. In the end, out of coal mining is mainly used to burn energy extraction, or said that coal like oil can be converted into other products, which is a coke can convert?
- Coke is not used for blast furnace ironmakingThe use of blast furnace burden include iron ore (natural ore, sinter and pellets), solvent (limestone or dolomite), and coke, charge from top order batch into the furnace. Coke in the blast furnace ironmaking can be summarized as follows:(1) provide the heat: coke in the coke oven in front of the raceway in the intense combustion, combustion heat generated in the blast furnace smelting process is the main heat source(2) reduction: high temperature gas generated in coke combustion in the raceway, passed to the material in the process of heat rising, the endothermic reaction and coke formation, CO and H2, then CO and iron oxide in iron ore reduction reaction is transformed into metallic iron.
- Q:In the coke analysis index, M40% and M25% respectively mean what?
- (2) mainly used in: Coal Science and Technology (first level), coal processing and utilization (level two), coal chemistry and coal quality analysis (level three)
- Q:What is the amount of waste gas produced by a ton of coke burning
- Process for producing coke, coke oven gas and coking chemical products by thermal decomposition and coking.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
Coke Breeze of 0-10mm
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 m.t.
- Supply Capability:
- 100000 m.t./month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
