China Mini Needle Valve/Small Needle Valve / API Gas Needle Valve
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 50 Sets set
- Supply Capability:
- 1200 Tons Per Month set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Packaging & Delivery of China Mini Needle Valve/Small Needle Valve / API Gas Needle Valve
Packaging Details: free fumigation plywood case or as buyers' requirements.
Delivery Detail: decision in consuctation with customers according our practical
Specifications of China Mini Needle Valve/Small Needle Valve / API Gas Needle Valve
1.OEM/ ODM are offered.
2.Pressure up to 6000 psig(414bar)
Features of China Mini Needle Valve/Small Needle Valve / API Gas Needle Valve
Pressure up to 6000 psig(414bar) for standard series
Pressure up to 10000psig(689bar)for high pressure series
Temperature from -65°Fto 450°F(-54°Cto 232°C)
With PTFE packing
Temperature from :-65°Fto 1200°F(-54°Cto 649°C)
With Grafoil packing
Safe union-bonnet construction
Back seating design protects the packing in fully open position
Panel mountable
Packing below stem thread isolates the thread
Lubricants from the media
Non-rotating stem tip
100%factory tested
- Q:Is the injection pressure tight after the valve pin closes?
- In the process of injection molding, solution and shrinkage because of cooling, but because the screw to move slowly forward, so that the material in the tube to melt into the cavity, to supplement the needs of shrinkage, called pressure. It means to prevent product shrinkage, with pressure if production is stable. The pressure can also adjust the product size, without weld line
- Q:How does a sequential needle valve work in a hot runner?
- The timing needle valve controls the injection of plastic by controlling the opening and closing times of the valve needle. General car door panels, car bumpers and so on must be used timing needle valve, of course, not demanding.
- Q:After the needle valve sealing, how to solve the cold material?
- The runner is the first and the runner is second, and the product is about third when it reaches 90%.
- Q:Working principle of needle valve type oiling cup
- I know this, I want to make a joint in the oil filler, can solve the leakage problem of inclined tubular Jiagen, but no drawings, do not know the specific circumstances not joint design
- Q:How can I see a needle valve in plastic products?
- Do good needle type mold, the glue inlet port is generally lower than the product surface, in front with no obvious signs of the case can be used to identify the surface color, into the plastic needle valve mouth is used with cooling gel, ambient temperature will be higher than the nearby, slightly shiny.
- Q:How long is the needle length of the needle valve?
- This problem is hot runner companies should pay attention to the problem, they will be based on the mold drawings to define the length of the needle, thickness and so on
- Q:What's wrong with the sealing ring at the needle valve of the spray gun?
- If the sealing ring break not leak does not affect the pressure, spray a shares is because the last time you painted not wash or spray gun, the valve needle sharp deformation, if often run out of the gun after cleaning will cause the spraying effect is not good, long lance clog, preferably after use with clean water that day!
- Q:Hot runner valve needle broken inside how to do?
- Then heat the drain plate and remove the needle from the distributor with the needle sleeve. Then the muskets firing valve needle sleeve, the glue burn clean, it can take out the needle valve. Hope to help you.
- Q:Mold glue is how the air valve needle
- The hot plate of the needle valve has operation instructions on it. If it is not clear for a long time, see if the hot runner leads out the interface. Is there any mark gas IN/OUT?If not, (usually two groups, only one group and one group)
- Q:Does the needle valve hot runner have adhesive problems? What are the possible causes?
- ExistingWe asked coreter hotrunner maintenance customer servicePossible reason: the valve needle does not emit too much heat.Handling: reduce hot nozzles and gatesThe temperature increases with cooling time.
1. Manufacturer Overview |
|
---|---|
Location | Beijing,China (Mainland) |
Year Established | 2003 |
Annual Output Value | |
Main Markets | 20.00% Mid East 10.00% North America 9.00% Eastern Asia 9.00% Africa 8.00% Northern Europe 7.00% Domestic Market 7.00% Western Europe 6.00% South Asia 6.00% Eastern Europe 5.00% Southern Europe 5.00% Oceania 4.00% South America 3.00% Central America 1.00% Southeast Asia |
Company Certifications | ISO 9001:2000;CE;API;ENVIRONMENTAL MANAGEMENT SYSTEMS CERTIFICATION CERTIFICATE |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | Tianjin,Shanghai |
Export Percentage | 71% - 80% |
No.of Employees in Trade Department | 11-20 People |
Language Spoken: | English, Chinese, Japanese |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
China Mini Needle Valve/Small Needle Valve / API Gas Needle Valve
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 50 Sets set
- Supply Capability:
- 1200 Tons Per Month set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches