Burner Valve with ISO9001-2008
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1000 Pieces pc
- Supply Capability:
- 8000 Pieces Per Day pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Packaging & Delivery of Burner Valve
Packaging Detail: carton, wooden case or upon request
Delivery Detail: within 15 days after receiving 30% deposit
Specifications of needle valve:
1,material:ss304,ss316,brass,copper
2,size:1/8"-1"
3,2-way handle valve
4,2-way valve
Nominal Pressure:6000psi
Applicable Temperature:≤150oC
Applicable Medium: Oil. Water. Gas and other corrosive or noncorosive medium
The Materials for Manufacture:304SS,316SS.316L,brass
The Demands for Fitting Pipes:Φ3 to Φ30
Cone Thread: ZG, R, GPT, NPT.etc
- Q:Is the injection pressure tight after the valve pin closes?
- In the process of injection molding, solution and shrinkage because of cooling, but because the screw to move slowly forward, so that the material in the tube to melt into the cavity, to supplement the needs of shrinkage, called pressure. It means to prevent product shrinkage, with pressure if production is stable. The pressure can also adjust the product size, without weld line
- Q:Napping needle valve type hot runner gate part of what is the reason? Do you have any expert answers?
- Needle valve type hot runner hot runner is high precision, the valve needle is one of the important components, effect of the needle valve material of hot runner system can not be ignored. As is known to all, the needle valve type is mainly the valve needle in the non-stop switch closed, thus controlling the feed and shut down.
- Q:The hero can help solve the valve pin, hot runner, into the gate, white spots problem?
- I'll give you a few suggestions, 1 valve needle valve needle end temperature, the temperature is too high will the glue burned 2, valve needle back and speed, when the back end of the needle valve will air the 3 mold thickness, temperature effect of gate region will be great, especially cold shear heat hot nozzle at the front end of the 4, this is very important, 5 hot tip white material cannot do without these problems point, hope this is helpful to you.
- Q:Hot runner mold valve needle sealing is lax, what are the reasons?
- General hot runner mold valve needle sealing is lax, the main reason is that the cylinder pressure is not enough.
- Q:Needle valve hot runner Road, needle valve does not move, what are the reasons?
- This has happened to me, too. There's no other way but to take the panel apart and take the splitter plate and the valve pin together with the needle sleeve.
- Q:How can I see a needle valve in plastic products?
- Do good needle type mold, the glue inlet port is generally lower than the product surface, in front with no obvious signs of the case can be used to identify the surface color, into the plastic needle valve mouth is used with cooling gel, ambient temperature will be higher than the nearby, slightly shiny.The needle tip of the valve will also have obvious marks, because the high temperature and the entrance of the glue hole will always be more or less bright or rough than that of the die steel.
- Q:What's wrong with the sealing ring at the needle valve of the spray gun?
- If the sealing ring break not leak does not affect the pressure, spray a shares is because the last time you painted not wash or spray gun, the valve needle sharp deformation, if often run out of the gun after cleaning will cause the spraying effect is not good, long lance clog, preferably after use with clean water that day!
- Q:How to use the needle type oil cup
- Method of use: D needle type oil cup is a cup, the cup is a middle upper lid, from the top to the bottom through a needle valve, the cup cover is bending spring, pressure spring pressure to the middle of the adjusting nut adjusting nut to adjust the valve pin to the top of the lower end of the oil outlet open the upper part, and sideways to erect it can put the valve open to the maximum.
- Q:Needle valve hot runner outlet hole shrink what is the reason?
- Because the valve needle is into the gate, the hot runner temperature here is the highest, so the plastic temperature near here is the highest. The higher the temperature is, the greater the shrinkage, so when the product is cooled naturally, the needle valve has the largest shrinkage hole.
- Q:A Kelon old air conditioning, fluorine mouth, there is no needle, how to measure the pressure and fluorine ah? No thimble tube screw, no response, how should I test? Thank you
- Inside the six angle valve clockwise turn to the point, plus good, and then shut to death, OK
1. Manufacturer Overview |
|
---|---|
Location | Beijing,China (Mainland) |
Year Established | 2003 |
Annual Output Value | |
Main Markets | 20.00% Mid East 10.00% North America 9.00% Eastern Asia 9.00% Africa 8.00% Northern Europe 7.00% Domestic Market 7.00% Western Europe 6.00% South Asia 6.00% Eastern Europe 5.00% Southern Europe 5.00% Oceania 4.00% South America 3.00% Central America 1.00% Southeast Asia |
Company Certifications | ISO 9001:2000;CE;API;ENVIRONMENTAL MANAGEMENT SYSTEMS CERTIFICATION CERTIFICATE |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | Tianjin,Shanghai |
Export Percentage | 71% - 80% |
No.of Employees in Trade Department | 11-20 People |
Language Spoken: | English, Chinese, Japanese |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Burner Valve with ISO9001-2008
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1000 Pieces pc
- Supply Capability:
- 8000 Pieces Per Day pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords