CH Self-propelled Scissor Lift

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Models of the Self-propelled Scissor Lift Platform:

Features of the lift:

1)Tilt sensor;

2)Proportional control;

3)Secondary emergsncy stop button mounted on base;

4)Platform overload and pressure loss valves as standard;

5)Emergency platform lowering mechanism;

6)Pull out storage drawer for cables and guardrail tools;

7)Wide forklift entry and transit strap points;

8)Smooth roll castors with non marking tyres;

9)Hole protection; Fault alarm system.

Q: What about the platform of southworth?: Sotheby's, is the first domestic lifting platform manufacturers, is the United States and domestic joint venture, wholly is now in Shanghai, the disintegration of the original taiyuan company, now in Shanxi Province are the original salesman themselves out to make small workshops, after what must not, guaranteed or wholly owned company in Shanghai, technology also has the backing of the United States, you can go to look at him!

Q: How does a button in the PLC control the elevating platform: Click on the rise to the top, and then the bottom? This can be used to refer to a button that controls an electric motor The elevating platform must have the upper and lower limit, and can not stop in the middle. Not safe.

Q: How does hydraulic platform change sealing ring, how to operate: Flange join type, should remove flange join screw first, use the screw to remove the end of the cover, can not lever or hammer, lest damage; Inside the card key type connection, should use a special tool, the guide sleeve toward the push, reveal the card key and hydraulic plunger pump used to () after remove the card key items with nylon or rubber texture the card key fill out again after its; Thread connection type oil cylinder, should screw the screw down first; In the demolition of the piston rod and the piston, not hard to pull out of the cylinder, piston rod components should try to keep the components of the piston rod and cylinder axis slowly pulled in a line.

Q: Where do the elevator motors go?: Electric elevators are widely used in factories, hotels, buildings, malls, stations, airports and stadiums. Can be used as a maintenance tools, paint decoration, change the lamps and lanterns, electrical appliances, cleaning and maintenance, power lines, lighting appliances, overhead pipeline installation and maintenance, air cleaning, etc. A high-altitude assignment for a single person. It can easily enter and exit the common entrance tunnel, and can enter the ordinary elevator to carry the multi-storey building work. The two phase power supply is used for the power, the infinitely variable speed, the user's high-altitude operation is safer, more convenient, the noise is small. It is ideal to use fast and convenient.

Q: The single fork hydraulic lift platform: According to your description, should be three four-way solenoid valve core card death return, can wash the unwrapped solenoid valve, check valve core have any injury, if the strain suggest replace the solenoid valve, hydraulic elevating actually single stage it is best to use support valve as a control valve, the failure rate will be lower,

Q: What device is better to design a platform that is 1 square meter or so?: Elevating elevator, lifting platform, four-wheel mobile elevator, aluminium alloy lift, fixed lift, rail lift, truck lift

Q: How to improve the oil leakage line: If it's an interface leak, you need to check if the interface is loose and the seal is broken. Or the interface design is not reasonable, you need to improve the interface.

Q: Who can tell me the purpose of the elevator? The more, the better: Single column aluminum alloy elevator: this series of products for indoor type, widely used in star hotel, such as the large supermarket industry lobbies, the aerial work inside the factory, has a balance, convenient operation, can enter the hall, can freely in and out of the elevator and less consumption, no pollution, work does not hurt the earth, can be used for wall and out work, work no dead Angle. The single column aluminum alloy electric elevator is fitted with the gantry cross attachment, which is suitable for the maintenance of movie theater, synagogue and church. The long door is easy to assemble, easy to operate, flexible to move, can span up to 1.1m fixed seat and other obstacles, and can stabilize the work on the step. High strength rectangular steel pipe making, rigid and stable. It is equipped with multi-wheel and flexible. Both ends can be adjusted, which can be used to cross different obstacles. The two sides are vertical adjustable, which can be used for the incline or step of a certain incline.

Q: Introduction of vertical elevator milling machine: Milling machine is a kind of widely used universal CNC machine tools, can be processed on milling machine plane (horizontal, vertical plane) and groove (key, T slot, dovetail groove, etc.), the points of tooth parts (gear, spline shaft, wheel), helical surface (screw, screw groove) and various kinds of curved surface. In addition, it can also be used for the surface of the rotating body, the inner hole processing and the cutting. Hope to adopt!

Q: The hydraulic cylinder with hydraulic platform is changed to whether the cylinder is feasible: Certainly not, the unit pressure difference is very big, not applicable..There must be no seal conditions.

Send your message to us

*Email

*TEL

*Quantity

*Unit