Butterfly Valve Without Pin Ductile Iron DN460

Ref Price:

Loading Port:: Tianjin

Payment Terms:: TT OR LC

Min Order Qty:: 5 set

Supply Capability:: 50000 set/month

Inquire Now

Add to My Favorites

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Cast Steel Flanged Gate Valves

Carbon Steel API Gate Valve

High Quality Check Valve

BS Gate Valve

Gas Gate Valve with Indicator

Gate Valve with Aluminium Hand Wheel Made in China

Valve Britain Stardard Made in China for Wholesales

Gate Valve BS5163 Made in China for Wholesales

Centerline structure,pinless double half shaft design.
Disc has two-way bearing, no installation direction requirements.
Non-backed replaceable seat with good performance and a longer working life.
Square and short neck for lable use and cost saving.
Easy installation, no need flange gasket.

Size	DN50mm-DN600mm
Design standard	API609/EN593
End flange	DINPN10/PN16, BS4504PN10/PN16, ANSI class125#/class150#
Face to face	API609/EN558-1
Top flange	ISO5211
Body	Ductile iron/Cast iron
Disc	Ductile iron/CF8/CF8M/C95400/C95500
Stem	SS420
Seat	EPDM/NBR/Viton/PTFE
Actuator	Bare shaft/Lever/Gearbox and handwheel
Coating	Epoxy/Nylon/PTFE
Pin	With out pin
Suitable medium	Water/Seawater/Sewage/Air/Foodstuff/Oil

Q:What are the common standards for gate valves?: Is the gate valve opening and closing parts, RAM direction of motion perpendicular to the direction of the fluid, valve can only be fully open and fully closed, can not be adjusted and the throttle. The following common standards for Fujian Biaoguang valve for valve: design specification: JB/T 7746, API602 JB/T 7746, the length of the structure specification / thread socket factory test and inspection of JB/T1751/GB7306, ANSI: B16.11/B2.1: JB/T 9092, API598 pressure temperature: GB/T 9131, ANSI B16.34, MSS GB/T 12220 product ID: SP25 delivery specification: JB/T 7928

Q:What is the difference between the cut-off valve and the gate valve?: Selection of stop valve:There are two ways to install the valve, one is the media flow from the top of the spool, the advantage is that when the packing is not under pressure, the pressure can be replaced before the valve packing, there is a long service life characteristics. Another is the media from the bottom of the spool into, and its shortcomings are driving torque is large, is 1 times above the flow, the stem by the axial force of large, easy to bend the stem. Generally suitable for small caliber manual stop valve, to stop the valve closed, the media acting on the spool of force is not greater than 350kg limit. Electric cut-off valve is generally used to enter the media from the top way.Selection of gate valve and stop valve:Valve than the valve structure is simple, better sealing, manufacturing and maintenance to be convenient; shortcomings are fluid resistance, power, and opening and closing efforts. Gate valve, stop valve are fully open, fully closed valve, suitable for making cut off, it is not suitable for use as regulating valve. The application process should pay attention to the characteristics of the valve when selecting. Small pipes and better sealing performance generally use cut-off valve; in the steam system and large diameter pipeline, due to fluid resistance is small, suitable for use gate valve.

Q:What is the wedge type gate valve wedge is what mean: It can be used on high pressure gate valve. Wedge gate and elastic wedge gate, gate and double gate. A, elastic ram. A circular groove is machined on the vertical bisector surface of the gate so that the gate plate has a certain elasticity. It is this elastic deformation, the gate is closed, the compensation gate sealing surface and the valve seat sealing surface between the wedge angle deviation, the arrival of good agreement, to ensure the sealing. Resilient gate valve sealing surface reliable. Applicable to a variety of pressure and temperature of small and medium-sized gate valve, requiring medium containing solid particles to less, in order to prevent congestion in the gate ring groove, affecting the flexibility of sealing.

Q:What are the structural differences between parallel and wedge valves?: The advantages of dual gate plate is sealed and angle precision low temperature is not easy to make the wedge gate, the abrasion of the sealing surface and shim.The disadvantage is that the structure is complex, easy to stick in the dry medium, mainly the upper and lower baffles. After years of corrosion, the gate is easy to fall off. Although the single gate is sealed and angle accuracy requirements are relatively high, difficult processing and temperature change may make the gate wedge and other shortcomings, but has the advantages of simple structure, reliable use, especially to the flexible gate, can produce the micro elastic deformation to compensate for the deviation between the sealing surface angle processing, which is widely used at present.For more information about valves, please keep an eye on the valve knowledge section.

Q:Gate valve z45h-10dn250 length of the body?: Z45h-10dn250 body length L=330mm, this valve is hidden bar, elastic seat, sealing gate valve, gate lining, lining fluorine, belong to soft seal

Q:What is the difference between the cut-off valve and gate valve, the general will use the cut-off valve instead of gate valve: Yes. Globe valves and gate valves are indeed common in certain piping and operating conditions.

Q:What is the soft seal gate valve?: Commonly used soft sealing gate valve model is divided into: Z45X and Z41X, the difference is that the Z41X is the Ming bar, and Z45X is dark rod.Matters needing attention in packing and transportation of soft sealing gate valve:Soft sealing gate valve before transport, should use the rope to tie up the small caliber.Before transportation, the lighter sides of the valve should be sealed.For larger caliber soft sealing gate valve, it should be used to carry out simple packing, it can better prevent the valve in the process of transportation damage.

Q:The legend of gate valve and stop valve: Compared with the cut-off valve, the main advantage is that the flow resistance is small, the flow resistance coefficient of ordinary gate valve is about 0.08~0.12, while the ordinary cut-off valve resistance coefficient is about 3.5~4.5. Opening, closing force is small, the medium can flow in two directions. The disadvantage is that the structure is complex and the height is large. The sealing surface is easy to wear. The sealing surface of the valve must be forced to close the valve to achieve sealing, in the same caliber, work pressure and the same drive device, the drive valve torque is 2.5~3.5 times the gate valve. This point should be noticed when adjusting the torque control mechanism of the electric valve.The sealing surface of the stop valve contacts each other only when the valve is completely closed, and the relative sliding amount between the valve core and the sealing surface is very small, so that the wear of the sealing cover is very small. The sealing surface of the valve cover, mostly due to the spool and sealing surface before the debris, or because of the closed state is not tight, causing the medium of high-speed erosion caused by.

Q:How to distinguish between gate valve and cut-off valve?: Two can be closed, in the flow of linear requirements are not high, you can adjust the flow. Just because of its structural characteristics of the valve to make its flow resistance, so there is a demand for throttling with a little more than the gate valve. In addition, the cut-off valve, whether it is a formal or reverse installed, in the opening and closing process, there is always a very difficult, and therefore can not do a great deal, or it is not easy to open and close. In addition, the cut-off valve has a one-way sealing effect of good features, so in the prevention of reverse flow of the working fluid, it also has a place to play.Hope to be of some help to you!

Q:What's the difference between the knife gate valve and the stop valve?: Minor force needed for opening and closing.Medium flow is unrestricted.When opening fully, the sealing surface is eroded by the working medium smaller than the cut-off valve.The shape is relatively simple and the casting process is better.The valve is used in the system is relatively large, to close the gate off system; and the valve is used in the system is relatively small, and to adjust the flow quantity of the system, can not be closed gate and globe valves of different specifications for many kinds of occasions, the valve rod valve the dark bar gate valve, wedge gate valve, single valve, multi valve valve body structure is different, large volume.

1. Manufacturer Overview
Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates
a) Certification Name
Range
Reference
Validity Period

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range