Plastic Tubes 2024 PPR Pipe for Landscape Irrigation Drainage System from China

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Q:We are going to buy a new fridge and we want one with an icemaker. the ideal place for it is about 32 feet (running the tubing) away from the water source. Is this possible to do? We are on a flat slab so we cannot run under the floors. it would have to be run up the wall, across part of the ceiling and under the sink.: You can. Most kits for water supply come with 15 or 25 ft of tubing. You might consider buying bulk 1/4 copper tubing so that you won't have any joints in spaces that you can't get to easily. One solid run would be best. If you were going to run the plastic tubing I have never seen it in lengths greater than 25 ft. If you cant get a longer piece you should be careful where you make a joint.

Q:Are plastic tubes resistant to chemical degradation?: Yes, plastic tubes are generally resistant to chemical degradation.

Q:Suppose I take a plastic tube and some insulated wire and wrap the wire very tightly around the plastic pipe so that the pipe is covered with several layers of wire wrap. The wire is always wrapped around the pipe in the same direction. Then we connect the two ends of the wire together. If I then drop a strong magnet down this pipe arrangement, will the magnet fall slowly, or not?: Not slowly, but it will fall somewhat slower because of an induced current when it first enters and exits the wire covered section of the tube. In the middle section the two poles will induce opposite induction currents (and voltages), so the effect will cancel. But if what you want it to show eddy current effects, the coil arrangement is not a good way of doing the experiment. You want the resistance to be minimal so the eddy currents don't dissipate too fast. And you want the eddy currents at both poles of your magnet to be (relatively independent) and not cancel out in a series circuit. The easiest way to achieve that is to use a simple copper tube. Of course, if what the question is trying to do is to test if YOU understand the difference between the coil and the solid copper, then it might actually achieve its purpose. I bet most people will get it wrong. Good Luck with your experiment. Or your homework question. :-)

Q:can you use rubber tubing to make moonshine?: HELL NO!!!! The heat from the still will melt the plastic, and even if it doesn't you will be getting tons of toxic **** from that hose screwing up every drop of ur shine, never use it unless going from the end of a worm to jar

Q:What is the difference between waste pressure plastic pipe and PVC pipe?: The same plastic pipe, the difference lies in the two properties and advantages are not the same, PVC plastic pipe is the main advantage of flame retardant, wide use, PE pipe can only be used in ordinary civil pipe;

Q:Can plastic tubes be used for fire extinguishing systems?: Yes, plastic tubes can be used for fire extinguishing systems. However, it is important to note that the type of plastic used must be fire-resistant or fire-retardant to ensure the safety and effectiveness of the system.

Q:How do plastic tubes compare to silicone tubing?: Plastic tubes and silicone tubing have different properties and uses. Plastic tubes are generally cheaper, more rigid, and have higher chemical resistance, making them suitable for industrial applications. On the other hand, silicone tubing is more flexible, heat-resistant, and biocompatible, making it suitable for medical and food-grade applications. The choice between the two depends on the specific requirements of the intended use.

Q:How are plastic tubes filled with liquids or semi-liquids?: Plastic tubes are typically filled with liquids or semi-liquids through a process called filling. This involves using specialized machinery and equipment to accurately dispense the desired substance into the tubes. The filling process may vary depending on the viscosity and specific requirements of the product being filled. It often involves using a combination of pumps, nozzles, and controlled pressure to ensure precise and consistent filling.

Q:PP-R what's the plastic tube?: PP-R plastic pipes are made of random polypropylene plastic pipes, generally used for water supply pipes. Hot melt welding.

Q:Can plastic tubes be used for fishing rod blanks?: Yes, plastic tubes can be used for fishing rod blanks. However, they are not commonly used due to their lack of durability and flexibility compared to traditional materials like graphite or fiberglass.

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range