2024 New Plastic PPR Pipes and Fittings for Irrigation from China
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 20000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Brief Introduction：
The comprehensive technical performance and economic indicator of PP-R are much better than galvanized pipe, UPVC pipe, polyethylene-aluminum compound pipe, PE-X (cross-linked polyethylene) and polybutylene pipe etc. For this reason PP-R is the leading products and widely used for feed-water piping in developed countries in Europe and America.
German Standard DIN8077 and DIN8078.
Nowadays PPR pipes win more attention and have been used all over the whole world more widely with its excellent sanitization performance, high heat resistance, compression resistance, corrosion resistance, pliability and seismic performance which make PP-R the real environmental friendly pipe.
Product Applications:
1.Distribution for cool and hot water
2.Duct for drinkable water system
3.Pipes for kinds of high-temperature and low-temperature heating system
4.Pipes for heating and cooling settings in solar energy system
Main Product Feature：
1. Light weight, easy and quick assembly
2. Most suitable for carrying drinking water
3. Excellent corrosion and chemical resistance
4. Bacteriologically neutral
5. Low thermal conductivity
6. Safe and watertight joints
7. Reduce heat loss
8. Resistance to scaling
9. Resistance to abrasion
10. Resistance to stray current
Advantages：
1, High Temperature Resistance: the maximum sustained working temperature is up to 70 Degrees Celsius, the maximum transient temperature is up to 95 Degrees Celsius.
2, Heat insulation and Saving Energy: low thermal conductivity which is only 1/1500 of brass pipe, and 1/250 of steel pipe.
Non-toxic: no heavy metal additives would not be covered with dirty or contaminated by bacterium.
3, Corrosion Resistant: resist chemical matters or electron chemical corrosion.
4, Lower Installation Costs: light weight and good hot-melt performance can reduce installation costs by as much as 50% over metal piping system.
Product Description:
Pressure | Size(mm) | Pressure | Size(mm) |
PN1.25MPA | 20*2.0 |
PN1.6MPA | 20*2.3 |
25*2.3 | 25*2.8 | ||
32*2.9 | 32*3.6 | ||
40*3.7 | 40*4.5 | ||
50*4.6 | 50*5.6 | ||
63*5.8 | 63*7.1 | ||
75*6.8 | 75*8.4 | ||
110*10.0 | 110*12.3 |
Product Show:
Our Factory:
- Q:Jump rope in the middle of the cut of plastic pipe role
- Increase rope weight. It is estimated that your rope is a cotton cord, which can easily jump dead rope. Installing this plastic tube adds a certain weight, thereby preventing the dead rope.
- Q:What are the common diameters of plastic tubes used for irrigation in agriculture?
- The common diameters of plastic tubes used for irrigation in agriculture generally range from 0.5 inches (12.7 mm) to 2.0 inches (50.8 mm).
- Q:I was wonder If Plastic Pluming Tubes Yes WITH end caps would work for pontoons if you know tell me Thx -Zac
- I have seen people use them before. They will not carry as much weight as comparable sized aluminum pontoons due to the weight of the pvc. I saw a paddle boat made from 8 or 10 pvc before for two people. THANKS SEATTLES for suggesting that site, I might try to build one.
- Q:My 99 Ford Escort has been making sloshy water sounds and whistling sounds on the passenger side of the car when I run the A/C. I have also noticed that the floor is damp on the passenger side only. If I look up under and behind the glove compartment there is a black plastic box that is covered with condensation within a few minutes of running the a/c. Based on what I've read, this problem is probably a blocked drain rather than the heater core (I live in Florida and haven't touched my heater in 6 months :P). Can anyone confirm? The noise has also been getting worse, I noticed the damp floor a week or two ago, but the water noises have only kicked up the past 2 days. Will running the a/c without fixing it permanently damage anything? If I can't locate the drain to unblock and have to take it into the mechanic, how much would I be looking at? Thanks!
- You are probably correct about the a/c drain tube. If it were the heater core, there would be a coolant smell and your coolant level would drop and by now the engine would be getting hot. It shouldn't cost that much to have someone open the drain tube, but you should be able to do it yourself. Look in the engine compartment on the firewall at approximately the center of the car just a little toward the passenger side of center. There should be a black rubber or plastic tube protruding and pointing down or down and back. You may need a piece of wire to snake up the tube to loosen whatever is clogging it. Be careful with the wire and don't just shove it all up in there. Just through the tube is far enough
- Q:An air core is no core except air.
- Cute, but I saw the punch line back with the first bird.
- Q:What are the advantages and disadvantages of PPR plastic pipes compared with steel pipes?
- Advantages and disadvantages are as follows:1, light weight: unit length, weight is only 1/6 of cast iron pipe;2, high strength: tensile strength of more than 45Mpa;3, small resistance: pipe wall smooth, no fouling, the same caliber pipe along the head loss is more than 30% lower than cast iron pipe, can save a lot of operation
- Q:How do plastic tubes compare to polycarbonate tubes in terms of impact resistance?
- Polycarbonate tubes generally have higher impact resistance compared to plastic tubes.
- Q:Are plastic tubes suitable for hot-fill applications?
- Plastic tubes are generally not suitable for hot-fill applications due to their low heat resistance.
- Q:What is a tube bird feeder?
- A okorder /
- Q:Are plastic tubes suitable for underwater applications?
- Yes, plastic tubes can be suitable for underwater applications. Many types of plastic, such as PVC or polyethylene, are resistant to water and corrosion, making them appropriate for various underwater uses. They are commonly used in marine industries for purposes like underwater pipelines, aquaculture systems, or submersible equipment. However, the specific type of plastic and the application requirements must be considered to ensure the tubes are compatible with the underwater environment.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
2024 New Plastic PPR Pipes and Fittings for Irrigation from China
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 pc
- Supply Capability:
- 20000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
