Plastic Film Recycling Machine Rubber Crusher
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 100 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
1. Application of Plastic crusher
.Low Speed Crushing Machine is desugned for various degraded materials generated from granulating injection moulding machine.
. It features stable work,no noise and dust pollution,even granule size of product,high safety,power saving and long service life.
.It adopts upper and lower cutters,and the cutter frame features,optimized design with better cutting performance,and is applicable for crushing hard and thick materials.
.The cutter is made of VC12MV material.
.Instant reclaiming system is optional for convenient operation.
.Immediately recycle the degraded materials for avoiding oxidation and smelt within 60s(drop the physical strength,stress and color of plastic after absorbing water evaporation pollution,improve the quality of shaping product and drop cost).
2.Description of Plastic crusher
Waste plastic recycling machine also can be called plastic shredder , designed for pieces of many kinds of material, suitable for all kinds of large volume, hard broken press block or not press block of material, shredding machine used to shred all kinds of plastic, rubber, tire, fiber, paper, wood, iron drum,aluminum , copper,waste electrical appliances, waste cable, industrial wastes, living garbage and other solid or hollow materials. has the advantages of uniform discharge, size control. According to the size of the material the client can choose single shaft shredder, biaxial shredding machine and four axis shredding machine.
3.Images of Plastic crusher
4. Features of Plastic crusher
Motor drive reducer through the bevel gear transmission, drive the rotor shear rotation at low speed. Was uniform distribution on the rotor after material into the cutting board with the stator cut board of space, material cutting board with the stator cut by rotor plate extruding and shearing and crushing, after crushing material discharge from the bottom of the crusher.
5.Advantages of our plastic crusher
. Reverse sensor, automatic machine protection against overload and jammed.
. High efficiency, energy saving, environmental protection.
. Product design advanced and reasonable structure.
. Speed is low, stable and reliable use.
. Discharging granularity is adjustable, wide application scope.
. Bearing adopts water circulation cooling, long service life.
. Shear plate wear small, long service life.
. extremely flexible machine can process a variety of different materials.
. The shear strength, discharging fine granularity.
. Multiple protection, machinery, electrical appliances, in accordance with the European Union CE standard.
- Q:I want to make a plastic lid ~ ~ big barrel gasoline barrel diameter of about 58cm ~ ~ want to own processing to use what machine? How much, approximately? Where can I sell it?Every year I have about 200 thousand orders of more than cover any kind of high efficiency ~ ~ automation machine?? Can the 2~10 million machine be satisfied? And is the maintenance cost of the machine expensive?
- I would help you estimate the lid weight about 500~600 grams, barrel diameter is 58cm, the forming area of fand 2642cm. Although the cap weight is small, but the forming area is large, in the selection of plastic injection molding machine is to be considered the largest area of injection equipment,
- Q:How much does it cost to run a disposable plastic basket factory?
- Fourth that's the raw material, like the black plastic basket. The main ingredients of this kind of product are Recycled HDPE and polypropylene. Estimated equipment and die investment is about three hundred thousand.
- Q:Packing belt above hasp can't get rid of buy a crusher can I directly broken is broken belt
- Crusher, crusher, plastic crusher, plastic crusher,
- Q:How to calculate the crushing capacity of a coal crusher?What's the formula?
- What are the main factors that affect the work of the jaw crusher?Generally, the main factors affecting the operation of jaw crusher are meshing angle and RevolutionIs the angle between the meshing angle of moving jaw and fixed jaw. According to the 32 degree calculation of the maximum meshing angle up. The actual use are less than 25 degrees, generally 1820 degrees. The meshing angle is too large, would break up the ore out of the cavity, sand production line, resulting in injury or damage to other equipment. At the same time as the meshing angle increases (crushing ratio increase) decreased productivity. Adjust the size of the mouth of discharge, will change the size of the nip angle. In real life, to adjust the size of the mouth of discharge according to the ore granularity requirements. Therefore, to ensure product size requirements, as far as possible amplification of discharge mouth is reasonable. Gape size can be adjusted by adjusting the block, on the relation between the regulation of discharge should pay attention to broken mouth size ratio and productivity.
- Q:In hard rock foundation construction, can not be carried out burst, crusher does not move. Is there any good way?
- Cutting machine cutting width; or hammer drilling; then using hydrochloric acid into the reaction -- so, there will be a lot of smoke; such a circle, forming a hole diameter of 1 meters. Then it can be built with static blasting.
- Q:PVC what's the best blade for plastic crushers?
- A better quality 6CrW2Si should be suitable for crushing and crushing most of the hard plastics, but the price is more expensive;
- Q:Points for attention of plastic recycling granulator
- 3, the main bearing room at both ends of the bearing parts burned, hand burning or noise, we should stop, repair and add butter. During normal operation, the bearing chamber butter once every 5-6 days.4, pay attention to find out the law of operation of the machine, such as: machine temperature, speed, speed, according to the situation, timely processing.5, the operation is stable, should pay attention to check the gap coupling agreement is too tight, to timely adjust some loose.
- Q:What material should be used for the plastic crusher screen?
- The grate below the plastic crusher is made of alloy.
- Q:The crusher can not be broken. What happened to the stone?
- Within a certain range, increasing the eccentricity of the eccentric shaft can increase the capacity of the crusher, but it also increases the energy consumption of the crushing unit weight of the ore.. The speed is too large, will have been broken in the crushing chamber of the ore to discharge, and blockage phenomenon, but to reduce production capacity, power consumption increases, therefore, there should be a jaw crusher optimum rpm.
- Q:Maintenance essentials of 300 kW generator rental system for recycled plastics machines
- The recycled plastic crusher is the ideal plastic machinery and equipment for recycling and processing of waste plastics. The correct maintenance and maintenance is the best way to prolong the mechanical life
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
Plastic Film Recycling Machine Rubber Crusher
- Ref Price:
-
- Loading Port:
- Shanghai
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1 set
- Supply Capability:
- 100 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords
