Gear Factory metal gears small OEM for rotary tiller parts
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 set
- Supply Capability:
- 10000 set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Material: | Steel,as requirements | Processing: | Forging | Pressure Angle: | 20 |
Place of Origin: | Zhejiang China (Mainland) | technology of material: | forging | technology of machining: | hobbing,shaving,grinding |
heatreatment: | nitriding,carburization | OEM: | is acceptable |
Packaging & Delivery
Packaging Detail: | packed in carton |
Delivery Detail: | 70days |
Specifications
1.produce as drawings
2.material will be as requirements
3.strictly quality control
4.OEM is acceptable
Products information:
1. suitable for many sorts of transmission system, such as agriculture tractor, wind power, truck and other industry zone.
2. material and precision can be as requirements.
3. we have complete gear machining equipments: gear hobbing machine, shaving machine, gear shaper, gear grinding machine, and our own heat treatment center. all of the production procedure are strictly controlled by ourselves, no cooperation procession, so we can sure the final products to meet your requirements.
4.each processing, strictly quality control
5.certificate: ISO9001, ISO/TS16949
- Q:How to find the damage of automobile flywheel ring
- If the above method is valid, the flywheel is worn out. If it doesn't work, it may be the starter problem.Another way is to observe the flywheel directly from the inspection port, while turning and watching
- Q:How does the gear ring match the starter? Is there a method of calculating the work type? Tell me about it. Thank you
- The parameters such as the length of the normal line and the thickness of the teeth also need to be measured from the flywheel ring to the center of the starter gear.
- Q:The number of planet gear is 20, the drive ratio is 7.5. The number of teeth of solar wheel and ring gear is required
- A gear train that has only one degree of freedom. A driver can determine actuator (planetary) movement, the original is usually the center wheel or tie;
- Q:How to deal with the bite gear of starter drive gear and flywheel ring gear?
- Suggest replacing gears!2, the starter gear and flywheel teeth are loose, gear fixed position due to force displacement, resulting in tooth biting!It is recommended to be tested and fixed in detail!
- Q:Such as the title, consult an expert with us auto parts "flywheel and gear ring assembly" pressing method. At present there is no mature cold pressing process???Yes, press assembly, gear ring to match with the flywheel, not the gear ring fault analysis!? is there a cold pressing?
- When the gear ring is loose, it can be confirmed from the installation opening of the flywheel housing starter. If the gear ring is loose, new parts must be replaced. When installing, the gear ring shall be heated in the heating box and then heated on the flywheel. After cooling, the flywheel can be fastened to the flywheel.When the tooth of the ring gear is worn unilaterally, the gear ring can be pressed down, the front face and the front face can be overturned, and then used on the flywheel.The examination of normal gear meshing, the flywheel rotation does not start, it should be regarded as the engine internal faults, such as crankshaft locking, piston stick cylinder, clutch card lag, which should be further observed. Check whether the clutch is damaged or stuck, check whether the fuel pump plunger is stuck and whether there is any foreign matter in the engine.
- Q:What is the function of the toothed ring clamp in the die?
- A V - shaped rib around a certain distance from the workpiece contour. The action of the ring clamp is to prevent the metal sheet other than the shear zone and into the shear zone during the blanking,
- Q:The clearance between the slewing ring gear and the drive pinion
- And gear accuracy, installation center spacing is related to ~! See the manual ~!
- Q:How does the gear radial runout tolerance affect the gear drive?
- The radial runout of the gear ring is caused by the misalignment between the center of the gear circle center and the center of the gear hole (or shaft) when the gear is machined (this is the main reason and the main influencing factor).
- Q:The roller is assembled by a certain number of rollers and roller racks, and the rollers roll on the tooth surface of the rack when engaged
- The roller is composed of a certain number of roller and roller assembly, engaged in roller rack on the tooth surface, which greatly reduces the friction engagement, improve meshing accuracy, reduce wear; the toothed rack and the gear ring is designed according to the characteristics of rolling wheel, involute shape different from universal rack, better able to engage and roller
- Q:Free car gear how to locate the school to start with the electric vehicle
- There is an error between the toothed ring and the starter of the car,
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Gear Factory metal gears small OEM for rotary tiller parts
- Loading Port:
- Qingdao
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 set
- Supply Capability:
- 10000 set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords