Q:Want to buy a chainsaw, ask the electric chain saw, good or gasoline, it is good to use ah?

Just like the high-end authentic MAKITA 16 inch chain saw, as long as more than 1000, the same high end Stier's gasoline saw will be more than 3000. If your workload is relatively large, the gasoline saw will buy at least 700 or more. The electric chain saw should buy at least 400 or more. The electric chain saw does not need to pump oil automatically, and the oil chain with automatic pumping is complicated and has many problems. Also, forget to mention that the cost of using gasoline saws is much higher than that of electric saws.

Q:Chainsaw, chain saw, saw and saw their difference in gas

Chainsaw, chain saw, saw the difference between gas and oil:Chainsaw, also known as "power saw, saw with electricity as the driving force, cutting tool for cutting wood, stone, steel, sharp edge. Split, stationary and portable saw blades are made of tool steel, round, strip, and chain like.

Q:How much power does the chainsaw 2000W consume per hour?

Half an hour, 1 degrees.Junior high school physics is not learned, 1 degrees of electricity is actually 1KW.H, we commonly known as 1 degrees.That is, an electric appliance, such as 1KW, is theoretically 1 degrees an hour.Your 2000W was 2 degrees in that hour.

Q:What brand of saw is good?

The saw blade is one of the most important components of the saw. If you have a circular saw, buy the best saw blade. The more saw teeth, the easier it is to cut

Q:What is the difference between the guide bar chain saw guide plate

Distinguish from saw chain configurationsThe saw chain of the single phase saw is a saw chain with a small 3/8 intercept, such as the 9190 saw chain of OREGONThe saw chain of a three-phase chainsaw is a saw chain with an intercept of 0.404, such as the 5968 saw chain of the 404 OREGON Stihl and the B3 saw chain of the tiger headSaw chain guide the general configuration of the 52004500 chain saw is 0.325 intercept have 3/8

Q:Electric drills, electric saws and so on. Under what circumstances should carbon brushes be used?

A carbon brush is used whenever a point drill or an electric saw is used. It is a device that transmits energy or signals between a stationary part of a motor or other generator or other rotating machine;If the power tools are stationary or not turned, they should be changed basically, unless the motor is burned;

Q:How safe is the use of electric saws?

The operation of electric chain saws and the points for attention are as follows:1, when the processed original strip is less than 1.5m of the conveyor, no work is allowed.2 、 before turning on the power, the switch of the electric chain saw must be switched off to prevent accidental start.3, start the material before starting the electric chain saw, idling 1 min, check whether the operation is normal or not.4. When starting or operating, the hand and foot shall not be close to the rotating parts, especially the upper and lower parts of the chain5, when the fuse or relay trip, should be checked immediately.

Q:Flashlight saw five mark board black, how is to return a responsibility?

You know the speed is not the same, marble machine much faster than the speed of the circular saw, so the wood on the high-speed friction sawtooth, fast temperature rise, and the marble machine forward speed is not fast, so wood and tooth contact surface temperature is very high, high to make wood burning degree.

Q:What happened to my sudden turning of the saw?

The passive bevel gear is meshed with the active bevel gear, and the passive bevel gear is connected with the nut by a small screw rod, and the nut is fixed on the chain in the nutSaw guide, the handle is made of hollow core pin is arranged in the sleeve body of plum, plum blossom sleeve body is fastened on the cover. The cover body is provided with a limited circle, plum blossom sleeve body is provided with a pressure spring, a pressure spring and a bolt, screw bolt coatThe nut is provided with a stiffening ring, and the bolt is used for fixing the chain saw bar guide plate and the right shell of the main machine, and the guide plate cover is covered on the cover body.