Pressure Pipe with Various Color PVC on Sale
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 mm
- Supply Capability:
- 1000 mm/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specifications
pvc pipe for water drainage
1.Specification of pvc pipe:40mm-400mm
2.Thickness of pvc pipe:1.2mm-7.0mm
3.ISO certified.
Properties of pvc pipes:
1. Material: pvc pipe unplasticized polyvinyl chloride
2. Standard: GB, ISO9001, ISO14001
3. Color: white pvc pipe, grey pvc pipe , etc.
4. Specific Gravity, g/cm3, 20(C): 1.35 - 1.55
5. Vicat Softening Temperature, (C) >=79
6. Longitudinal Reversion, %, 150(C) <=5
7. Dichloromethane Resistance Test: No attack
8. Falling Weight Impact Test, TIR, %, 0(C) <=10
9. Tensile Yield Strength, Mpa >=40
10. Fitness of Water Tightness Test: No Leakage
11. Fitness of Air Tightness Test: No Leakage
Features of pvc pipes :
1) Light weight, easy to load and unload: PVC pipe is very light, convenient to handle loading unloading, and installing.
2) Good chemicals and drugs resistance: PVC pipe has its excellent resistance to the erosion caused by acids and alkalines, a great help to the chemical industries.
3) Small resistance to fluidity: The smooth surface reduces resistance to the fluids. Its roughness coefficient is only 0.009, much less than other pipes, Under same discharges, smaller cabibre of the pipe can be uesd.
4) Strong mechanical strength: Good resistance to water pressure, outside impact and pressure, is satisfied under any conditions.
5) Good electrical insulation: excellent insulation nature against electricity. the pvc pipe can be served as conduits and pipes in construction cable and wire.
6) Water quality unaffected: The solution tests on the PVC pipe show no affect on water quality when the water flows through is. It is considered the best piping material for running water works.
7) Simple installation: Very easy to connect, thus much time and laborcost may be saved.
Application of pvc pipes:
1) Structure Engineering, home water supply and drainage |
Specifications of the pvc pipe:
Outer Diameter (mm) | Wall thickness(mm) | |||||||
2.5MPA | 2.0MPA | 1.6MPA | 1.25MPA | 1.0MPA | 0.8MPA | 0.63MPA | ||
φ20 | 20*2.3 | 20*2.0 | ||||||
φ25 | 25*2.8 | 25*2.3 | 25*2.0 | |||||
Φ32 | 32*3.6 | 32*2.9 | 32*2.4 | 32*2.0 | ||||
Φ40 | 40*4.5 | 40*3.7 | 40*3.0 | 40*2.4 | 40*2.0 | |||
Φ50 | 50*5.6 | 50*4.6 | 50*3.7 | 50*3.0 | 50*2.4 | 50*2.0 | ||
Φ63 | 63*7.1 | 63*5.8 | 63*4.7 | 63*3.8 | 63*3.0 | 63*2.5 | 63*2.0 | |
Φ75 | 75*8.4 | 75*6.9 | 75*5.6 | 75*4.5 | 75*3.6 | 75*2.9 | 75*2.3 | |
Φ90 | 90*10.1 | 90*8.2 | 90*6.7 | 90*5.4 | 90*4.3 | 90*3.5 | 90*2.8 | |
Φ110 | 110*10.0 | 110*8.1 | 110*6.6 | 110*5.3 | 110*4.2 | 110*3.4 | 110*2.7 | |
Φ125 | 125*11.4 | 125*9.2 | 125*7.4 | 125*6.0 | 125*4.8 | 125*3.9 | 125*3.1 | |
Φ140 | 140*12.7 | 140*10.3 | 140*8.3 | 140*6.7 | 140*5.4 | 140*4.3 | 140*3.5 | |
Φ160 | 160*14.6 | 160*11.8 | 160*9.5 | 160*7.7 | 160*6.2 | 160*4.9 | 160*4.0 | |
Φ180 | 180*16.4 | 180*13.3 | 180*10.7 | 180*8.6 | 180*6.9 | 180*5.5 | 180*4.4 | |
Φ200 | 200*18.2 | 200*14.7 | 200*11.9 | 200*9.6 | 200*7.7 | 200*6.2 | 200*4.9 | |
Φ250 | 250*11.9 | 250*9.6 | 250*7.7 | 250*6.2 | ||||
Φ315 | 315*15.0 | 315*12.1 | 315*9.7 | 315*7.7 | ||||
Φ400 | 400*19.6 | 400*15.3 | 400*12.3 | 400*9.8 | ||||
- Q: Is hot melt hose toxic and harmful?
- Hot melt pipe using imported Teflon liner, has good flexibility, anti adhesion and resistance to high temperature (up to 250 degrees), can greatly reduce the carbonization phenomenon;
- Q: How to make a rubber tube requires flow
- The characteristics of the rubber tube has physiological inertia, UV resistance, ozone resistance, resistance to high temperature (-80 to 300), high transparency, strong resilience, resistant to compression permanent deformation, oil resistance, impact resistance, acid and alkali resistance, wear resistance, flame resistance, voltage, conductive properties.
- Q: What is the essential difference between silicone tube and rubber tube?
- Silica gel tube has high and low temperature (-60 ~ 200 DEG C), environmental protection, non-toxic, excellent heat aging, ozone aging resistance, light aging and aging resistance, soft, arc resistance, corona resistance.Silicone hose is the biggest feature of resistance to temperature changes of -60 degrees to 250 degrees, but the cost is very expensive, no requirement for the hose. Compression resistant silicone hose resistant to pressure can also be.
- Q: What is a rubber core pulling method?
- The hose shall be filled with water or gas at a pressure of 0.5 0.8N / mm before pouring concrete. At this point, the hose diameter can be increased by about 3mm. When pouring concrete, the vibrating bar should not touch the hose, and should check the pressure of the water meter regularly. If there is any change, the pressure must be filled.Smoke tube longer than tube core pulling slightly later. Before the pipe is pumped, the water is lowered and the pipe section is reduced, and the pipe can be drawn away from the concrete. The order of pumping is usually first, then first, then first, then straight.
- Q: Diameter 127mm steel pipe, and diameter 127mm rubber hose how to connect?
- Connection method:1, send special purchasing rubber pipes, as far as possible to choose the correct tolerance.2, if the work pressure is not more than 0.7MPa, the end of the steel pipe can be in accordance with the rubber tube inside the car, a knife.3, the processing of a casing.
- Q: What about leakage of hose joint?
- Sleeve joint event Water Leakage, you may need to remove the connector and reinstall the many water pipes, it should be timely reporting the repairman to repair.
- Q: Is it feasible to use rubber material, middle canvas layer and outer rubber material in PVC rubber tube?
- Improvement measures: 1, adjust the process, plastic material in place; mixing rubber plastic stability; vulcanized rubbing with low temperature long time vulcanization; 2, test cloth in curing temperature shrinkage coefficient is too big, consider changing cloth;
- Q: The selection of valves and fittings has the following requirements
- The selection of hose inner screw thread joint can be rotated, because not hose and the joint body can rotate freely after buckling, configuration of internal thread after disassembly for hose.
- Q: How to identify the quality of rubber pipes for sewage treatment?
- The general hose inside and outside the adhesive layer material with natural rubber, styrene butadiene rubber or butadiene rubber; hose with chloroprene rubber, nitrile rubber; acid and alkali resistant, high temperature resistant hose with ethylene propylene rubber, fluorine rubber or silicone rubber etc.. Structure: hose structure is usually divided into inner layer, outer layer and skeleton layer (or middle layer). The inner layer directly bears the abrasion and erosion of the conveying medium; the outer rubber layer protects the inner part of the hose from the damage and erosion of the external environment; the stock price is the pressure bearing layer of the rubber tube, and gives the strength and rigidity of the tube body. The working pressure of the hose depends on the material and structure of the skeleton.
- Q: Difference and application of rubber joint and rubber expansion joint
- The utility model can be used to reduce the vibration and noise of pipelines, and can compensate for thermal expansion and cold contraction caused by temperature changes. Rubber expansion joints are used in chemical, construction, water supply and drainage systems!
Send your message to us
Pressure Pipe with Various Color PVC on Sale
- Ref Price:
-
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 100 mm
- Supply Capability:
- 1000 mm/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
