Nut Coke of 20-50 mm
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Weexport many kinds of coke, such as CSR64 % and CSR 62 metallurgical coke (metcoke), the NUT coke of 20 to 50 mm, coke breeze of 3 to 6 mm, and so on.
We can offer belowgrade Nut Coke of 20-50 mm, origin from China.
ITEM GUARANTEED REJECTION
MOISTURE (as received) 8%MAX DEDUCTION FROM B/L WEIGHT.
ASH (dry basis) 13.5%MAX ABOVE14%
VOLATILEMATTER(dry basis) 1.5%MAX ABOVE1.9%
FIXED CARBON (dry basis) 85%MIN BELOW 83%
SULPHUR (dry basis) 1.0%MAX ABOVE1.3%
SIZE: 20-50MM 90%MIN
(-) 20MM 5%MAX ABOVE10%
(+) 50MM 5%MAX ABOVE10%
Let me know your demands then I can check availability.
- Q: What are the main uses of coke
- A small smelting industry, used to produce calcium carbide, carbon disulfide, phosphorus etc.. In the iron and steel enterprises, coke powder is also used as sintering fuel. Coke can also be used as raw material for the preparation of raw materials for the synthesis of water gas. ??4, in order to make the blast furnace operation to achieve better technical and economic indicators, smelting coke (metallurgical coke) must have the appropriate chemical and physical properties, including the smelting process of thermal properties.
- Q: What is the difference between coking plant and coke plant
- Production equipment and production processes are complex.Coke plant, generally only the coal into coke on it, so simple.
- Q: Who knows the proportion of pig iron and coke used in Cupola
- There are doubts: blank parts output is too low.3, blank export rate: raw materials into melting after the formation of blank, under normal circumstances, the common casting investment for every 1 tons of pig iron, scrap steel and other major raw materials, the lowest to 85% iron, after casting output blanks, nozzle, nozzle, riser, riser for iron smelting water ratio of about 30%; blank standard export rate, nozzle, riser re melted continue after put into use; production enterprises invested 1 tons per dryer, iron scrap and other major raw materials to the lowest 85% of the hot metal, roughly the same with ordinary casting, casting blank after the (standard yield) for hot metal ratio is about 70%, water riser for hot metal ratio is about 15%, and the same outlet riser re melted after continued use.
- Q: What kind of coke is needed for smelting special steel
- It is necessary to add coke, pellet, sinter ore, ore and other materials into the blast furnace in a certain proportion, batch and sequence, and then to produce molten iron in the reducing atmosphere of the blast furnace
- Q: With the number of 1 tons of steel smelting coke
- The use of coke pig iron smelting blast furnace, for each different, which is each blast furnace coke ratio (the ratio of the iron smelting a ton of coke by iron determined how many meals). The country or the world, the iron and steel enterprises coke are not the same, the coke rate is as low as possible, but there are many factors which restrict the level of coke, such as advanced level equipment, raw material and fuel quality, or the operator level, advanced process and so on many factors which influence
- Q: What is the difference between the industrial analysis of coke and the industrial analysis of coal samples
- Quite a lot! You'd better look at the standard coal GB/T212-2008,
- Q: What are the requirements for the quality of coke in blast furnace smelting
- 4, volatile in coke: according to the volatile content of coke can determine the maturity of coke. Such as volatile content is greater than 1.5%, is said to produce coke; volatile less than 0.5 - 0.7%, it is said to be overdone, the general maturity of metallurgical coke volatile is divided into about 1%.5, the moisture in the coke: water fluctuations will make the measurement of coke is not allowed, resulting in fluctuations in furnace conditions. In addition, the increase in the moisture content of Coke will make the M04 high, M10 is low, the drum index error.6, the screening of coke composition: in the blast furnace coke particle size is also very important. In the past, the particle size of coke in our country is as follows: the coke size of large coke oven (1300 - 2000 square meters) is greater than 40 mm; the coke size of medium and small blast furnace is larger than 25 mm. However, some of the steel test shows that the coke particle size of 40 - 25 mm as well. Larger than 80 mm of coke to be whole, so that the particle size range. The coke block is uniform, the gap is large, the resistance is small, and the furnace condition runs well.
- Q: Coke in the whole process of steelmaking in the end is what to do, just to provide heat or carbon and other substances into steel or iron?In the study of coal classification inside, one is divided into coking coal, coking coal and coke as main, and then you see is steel or iron coke must material. What is not clear. In the end, out of coal mining is mainly used to burn energy extraction, or said that coal like oil can be converted into other products, which is a coke can convert?
- 3) skeleton: smelting process in blast furnace is gas rise and decline occurred in the opposite charge of movement and interaction, the core permeability is the key operation of blast furnace. In the upper column, gas flow distribution of coke layer; in the middle of the column material, the coke from the skeleton effect, support has been melting the iron ore, the normal gas rise; in the lower column, high temperature in the solid massive existing coke and has become liquid hot metal and slag mixed together, become loose skeleton gas rising and falling iron and slag.
- Q: Coke crushing, coke plant equipment, coke jaw crusher, coke crushing equipment prices, manufacturers offer? How is the output of these equipments?
- The number of cracks has a direct impact on the strength and crushing strength of the coke, the index is generally measured in terms of crack degree (the number of cracks in the unit volume coke)
- Q: What is the difference between coke and coking coal
- Coke: a solid fuel, hard, porous, high calorific value coal. High temperature carbonization made for ironmakingTypes of coke:Coke is usually divided by use of metallurgical coke (including blast furnace coke, coke and iron alloy coke, calcium carbide and coke gasification etc.) with coke. The pressurized pulverized coal forming coal, coke carbonization etc. in the new postprocessing process called Formcoke.
Send your message to us
Nut Coke of 20-50 mm
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords