LED FILAMENT CANDLE LAMP BULB 4W NEW DEVELOPMENT
- Ref Price:
-
- Loading Port:
- Shekou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 500 pc
- Supply Capability:
- 10000000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specification
Product characteristic
1. High brightness LEDs
2. Long life service, lasts up to 30000hr
3. Excellent weathering resistance, insensitive to humidity, suitable for wide range temperature
4. Easy to install, easy to use
5. No strobe flash, speedy start, no flicker, good for eyes
6. Safe, energy-saving, environment friendly
Item | Parameter | ||
Power | 4w | ||
LED Quantity | 96pcs LEDs | ||
Colors | Warm white, white, cool white | ||
CCT | 2500-6500K | ||
Ra | ≥75 | ||
Lifespan | 30000-50000 Hours | ||
Light flux | 300LM | ||
Light efficiency | 100LM/W | ||
Glowing | 360° | ||
Material | Glass, Aluminum | ||
Net Weight | 0.031KG | ||
Gross Weight | 0.045KG（1/pc） | ||
Size | ￠35*118m ￠35*138m | ||
● Technical request | |||
Item | Units | Parameter range | |
Working environment | ℃ | -370C - 550C | |
Humidity | RH | ≤90% | |
Storage condition | ℃ | -40℃~80℃ | |
Limited voltage | V | AC85-265V 50Hz | |
Protect a Grade | IP20 | ||
● Application Scopes |
Suitable for most indoor lighting applications, such as household, hotel, shopping mall, supermarket, office, car park, factory, advertising box, car, vessel and other transportations, can significantly reduce the energy consumption; give you a green light environment |
- Q: LED what is the glue between the aluminum base of the bulb and the cooling aluminum?
- It's best to use heat conductive glue, such as ST922.
- Q: What are the requirements of the LED series inspection specification for bulb bulbs?
- Dielectric strength: electrical endurance test (resistance test) followed by insulation resistance test. During testing, the following AC voltage is applied at the specified position 1min. Type HV (220~250V); 4000V (RMS), BV (100~120V); 2U (rated voltage) +1000v.
- Q: I want to ask for high power LED bulb lamp wire inexplicably broke, and in large quantities. Is the quality of the lamp?
- The second continued the problem: welding line, this work continued not done!
- Q: LED can the bulb be used in the bathroom?
- Ordinary bulbs can be used in the bathroom, the bath water, protection grade ordinary bulb is not high, it is easy to make when water vapor lamps or rust element short circuit failure and cause some accidents. The bathroom is suggested by the power supply lamp, lamp waterproof plate etc..
- Q: What does the LED bulb patch mean?
- The LED patch (SMD) is made of FPC circuit board, LED lamp and high quality silica gel sleeve. Waterproof performance, using low voltage DC power supply is safe and convenient, light colors, bright colors; outdoor use can be anti UV aging, yellowing, high temperature resistance and other advantages, the products are widely used in building lights, decorative lighting, advertising and entertainment quasi decorative lighting lighting field.
- Q: LED bulb after the power failure, still glimmer, can last hours or even all day, what is the reason?!
- Because LED's normal luminous current is 20MA, and LED has a weak current, it can emit light. According to this source. Maybe your line is just on the zero line. This will lead to a small leakage current flows through the LED lamp.Try offline.
- Q: Is it possible to manually weld LED bulb bulbs?
- You can ignore the effect of heat conduction and thermal grease, solder is better, I was doing a lot of tests, the thermal conductivity of thermal grease is about 1.2 to 2, aluminum more than 300, thermal grease just to fill the bottom of the LED and the aluminum substrate contact surface gap, you don't fill gaps don't hinder it the normal contact with the aluminum substrate at the bottom of the LED, will be lost, and the use of thermal grease you for about a year will have to replace the thermal grease, only unscrupulous vendors will deceive others say I added thermal grease, heat conduction effect is not fully qualified, in fact, for a long time, the potential will LED light spot the chip inside the loose because of the long-term high temperature, causing the current growing, until completely off
- Q: Is there any flicker in the LED bulb?
- That should be a combination of small power and multiple LED lights! The main reason is the strobe power problem, to tell the truth, I do not set the LED power supply, improvement in the well to be unable to give you much help, our production of LED products, the procurement of materials and parts suppliers will request strobe or in the power supply design problem, if you want to buy LED products, especially is the bulb, I suggest you buy a large power assembly (i.e., the shell is Aluminum Alloy)!
- Q: LED bulb lamp. Is there a good drive or no drive? Is the lamp of good or integrated?
- LED bulb lamp, are driven by a power of the ordinary small beads, driving is very simple only rectification, filtering, limiting the number of components is another large power SMD beads, this drive is more troublesome, SMT SMD components, and double plate, both have the element.
- Q: What does "A19" mean in LED A19 bulb?
- A represents the bubble type, A hemisphere bubble 19, and the back figure indicates the bubble size (mm in diameter)
Send your message to us
LED FILAMENT CANDLE LAMP BULB 4W NEW DEVELOPMENT
- Ref Price:
-
- Loading Port:
- Shekou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 500 pc
- Supply Capability:
- 10000000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
Related keywords
