Plastic Coil Pipe Fittings - High Quality Threaded Union with Long Elbow for Water Heater
- Ref Price:
-
$3.30
/ watt
- Loading Port:
- Ningbo
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1000 watt
- Supply Capability:
- 100000 watt/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
ppr fittings HYOSUNG PPR raw materials standard:DIN8077-8078 GB/T18742.3-2002 PN25 White grey green color
1.Material:Random Polypropylene(Hyosung R200P);
2.ISO9001&ISO14001;
3.Standard:GB/T 18742.3-2002, DIN8077/8078;
4.OEM also ok
- Q: What tools and methods are needed for the installation of plastic hoses and steel tubes?
- (1) quantity. When the storey height is less than 4 m, the riser shall be provided with a telescopic joint on each floor; when the storey height is greater than 4 m, the design shall be determined according to the design expansion amount, and the maximum allowable amount of expansion shall not be greater than the expansion joint(2) site. The construction units often think that as long as the drainage pipe is provided with a telescopic section can satisfy the requirement, even as the expansion joint connecting pipe joints, Water Leakage caused by seepage, the correct approach is socket expansion joint should be set along the direction of flow, when the drainage pipes in the floor below access riser expansion joints should be set under water confluence pipe; when the drainage pipes in the floor above the access riser section should be arranged on the telescopic water confluence pipe; drainage pipes in the floor and upper and lower access, should be located in the middle section of the telescopic floor. At the same time, when the riser passes through the floor as a fixed support, the expansion joint can not be fixed, and when the contraction section is a fixed support, the riser can not be fixed through the floor. A telescopic joint arranged on the transverse pipe shall be arranged at the end of the water current converging pipe fitting.
- Q: PE is the hot melt?
- No, PE links can be fused by two ways, hot melt.
- Q: What are the common sizes of plastic pipe fittings?
- The common sizes of plastic pipe fittings vary depending on the specific application and industry. However, some commonly used sizes include 1/2 inch, 3/4 inch, 1 inch, 1 1/4 inch, 1 1/2 inch, and 2 inches. These sizes are widely available and used in plumbing, irrigation, and other piping systems.
- Q: Are plastic pipe fittings resistant to ultraviolet (UV) rays?
- Yes, plastic pipe fittings can be resistant to ultraviolet (UV) rays. However, the level of resistance may vary depending on the type of plastic used in the fittings. Some plastics, such as PVC (polyvinyl chloride), are naturally more resistant to UV rays, while others may require additional additives or coatings to enhance their UV resistance.
- Q: Do plastic pipe fittings require any special protection against UV exposure?
- Yes, plastic pipe fittings do require special protection against UV exposure. UV rays can cause degradation and weakening of plastic materials over time. To protect against this, it is recommended to use fittings that are made with UV resistant materials or to apply a UV protective coating to the fittings. This will help to extend their lifespan and maintain their structural integrity when exposed to sunlight or other sources of UV radiation.
- Q: Can plastic pipe fittings be used for chemical injection skids?
- Yes, plastic pipe fittings can be used for chemical injection skids. Plastic pipe fittings are commonly used in various industries, including chemical and petrochemical, due to their corrosion resistance and durability. However, it is important to select the appropriate type of plastic material that is compatible with the specific chemicals being injected to ensure safe and efficient operation.
- Q: How are plastic pipe fittings manufactured?
- Plastic pipe fittings are typically manufactured through a process called injection molding. In this process, plastic resin is melted and injected into a mold cavity, which is shaped like the desired fitting. The resin is then cooled and solidifies, allowing the fitting to be ejected from the mold. This method enables mass production of plastic pipe fittings with consistent quality and precise dimensions.
- Q: Water supply and drainage, fire pipeline installation, pipe installation has been included in the quota, if adding the elbow, three links should be the cost of materials, in which the items below?
- If not, the following supplementary material quota and modify the material cost of the corresponding name, unit, quantity, unit price.
- Q: Are plastic pipe fittings resistant to alkalis and acids?
- Yes, plastic pipe fittings are generally resistant to alkalis and acids.
- Q: Can plastic pipe fittings be used in fish tank systems?
- Yes, plastic pipe fittings can be used in fish tank systems. They are commonly used for plumbing and water flow management in aquariums due to their durability, corrosion resistance, and affordability. However, it is important to choose fittings that are specifically designed for use in aquatic environments to ensure they are non-toxic and safe for the fish and other aquatic life.
Send your message to us
Plastic Coil Pipe Fittings - High Quality Threaded Union with Long Elbow for Water Heater
- Ref Price:
-
$3.30
/ watt
- Loading Port:
- Ningbo
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1000 watt
- Supply Capability:
- 100000 watt/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
Hot products
Hot Searches
Related keywords
