H2000 Series 9T Dock Forklift Truck

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

You Might Also Like

Model		CPCD90-Wx
Power type		Diesel
Load capacity	kg	9000
Load center	mm	400
Lifting height	mm	1400
Overall length	mm	5103.5
Overall width	mm	1940
Overall height (overhead guard)	mm	1745
Min. turning radius	mm	4000
Travel speed(with/without load)	Km/h	20/22
Service weight(with oil)	kg	10200

Mainly applied in shipbuilding and ship-repairing yards for operations inside docks, with low vehicle height and strong climbing capacity;

Equipped with Wuxi diesel engine CA6110, with strong power and good acceleration;

Superior thermal performance with air-cooled heat emission, suitable for cabin operations；

Electro-hydraulic reversing, reliable and flexible operation.

Q:Do forklifts need to be measured?: Trade settlement, security protection, health care, environmental monitoring, your forklift belongs to which category, if it does not belong to do not check. Consult the local quality supervision bureau.

Q:What is the cause of my forklift: There are a lot of reasons why you can't start, and the owner doesn't say whether it's an internal combustion fork or a forklift truck.

Q:The operation procedure of forklift truck: (4) loading and unloading (1) fork materials, should according to need to adjust the distance between two goods fork, make the two forks load balancing, not skewed, items side should be posted on the shelves, fork in weight shall comply with the provisions of the curve of load center sign. (2) the carrying capacity shall not obstruct the sight of the driver. In the course of loading and unloading, the brake forklift must be used. (4) when the goods are approaching or exiting the goods, the speed should be slow and steady, and the wheel should not be rolled over the items, wooden pads, etc., so as not to be crushed by the roller. (5) when taking goods with a fork and fork, the cargo fork should be as deep as possible in the load, and the tip of the fork cannot touch any other goods or objects. The minimum door frame should be used to stabilize the load, so the load will not slide backward. When the load is put down, the door is small enough to allow the load and the fork to be drawn. (6) the high speed forked goods and the collision between the fork and the hard object are prohibited.

Q:What if the forklift oil is burned and the oil is burned: I often encountered this kind of problem Generally have can solve the hand pump pump oil pressure under the condition of no pressure generally Oil is the oil pipe leakage Find a flat place If can't solve suggest the oil all check it again Whether there is supervision way broken place And also when you exhaust Is there a burst of to take a breather One is when you finished exhaust The exhaust valve after fastening increase pressure in oil pump for several times repeatedly

Q:What are some of the common failures of forklifts?: Forklifts cannot be started with the following conditions: 1, the battery without electricity Failure of starter The key switch is bad 4, the oil pump does not supply oil 5, there was no oil tank 6, no oil 7, the crankshaft lock The engine was completely scrapped

Q:What procedures are required for a forklift licence: Are you on your way? The forklift belongs to the enterprise car, not the license plate!

Q:What is the safe speed of the forklift truck: Forklift truck speed can be set, internal combustion forklift usually have speed limiter, domestic forklift factory basic restrictions in 18-20 km/h, battery forklift truck speed can be set according to the request of the buyer the speed of the Settings for each mode.

Q:How does flexsim implement a forklift truck to move the product to the shelf: Double-click the staging area to check "use transport" for the temporary entity flow TAB.

Q:What the forklift needs to be aware of...: The forklift truck is prohibited from taking the goods at high speed and forbidding the personnel to stand on the fork; When taking the cargo work, the personnel are not standing around the fork, so as not to be hurt. The driver should check the crane chain, the door frame, the cargo fork, and whether the bolt is firm. Check for fuel oil, lubricating oil, check start-up, operation, and braking performance. Check the light and sound signal to be fully valid and confirm normal restart operation. After starting the engine, listen to the operation of the engine and check the instructions of each instrument. When there are mechanical problems, you can't repair yourself. You should close the forklift and inform the mechanic. The driver should observe four weeks before the start of the forklift truck. The carrier will start off slowly and smoothly and make sure the cargo is stable and reliable.

Q:Does anyone know what is the principle of explosion protection forklift truck?: Explosion-proof forklifts are generally common forklift to take professional explosion-proof processing, after the acceptance of (acceptance according to the national standards and certification) to sell, you can find out if you want a local forklift dealer, they can contact the factory to do, it is can't do it myself

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range