80W waterproof led outdoor flood lights with UL/CE Certification

Inquire Now

OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing

China National Building Material Group Corporation. CNBM Group ranks 267^thof the Globe Fortune top 500enterprises. Stainless Steel is one of the main productsofCNBM. We are specialized in all kinds of led products, such as Flexible LED Strip,Rigid LED Bar, LED Tube, LED Bulb, LED Panel, Spot lights,

80W waterproof led outdoor flood lights with UL/CE Certification

contacts

If Any Inquiry, Pls feel free to contact Miss Elaine.

Contact: Elaine Mei

Tel/Whatspp:+86 15251575665

Email:elainemei(at)okorder.com

Q:Rated voltage of LED lamp string: You are the light string and see how much you a lamp, the lamp voltage for LED in 3.0-3.4V, for intermediate values of 3.2V, N=220/3.2=68.75 so many beads. In fact, we are in terms of LED is a DC device, there is no voltage rating, mainly to see his current value, the work must be steady flow. The power 0.06W LED current is 20MA, the power 0.2W LED current is 60MA, the power is 0.3W, the LED current is 100MA, the power is 1W, the high power LED current is 300-350MA, and so on in turn, ah, I=P/U

Q:The number of lights in the LED string: In general, 1210 specifications of the band is 60 LED per meter, 5050 specifications of the band is 30 LED per meter, the special has 60 LED per meter.

Q:How much is the voltage across the 20 LED lamps in series?: LED lighting general LED lamp belt voltage, conventional specifications are 12 volts and 24 volts, if it is 12 volts, that voltage is 420 volts, if it is 24 volts, that is 840 Volts

Q:220vled water lamp string how to connect, that is, 220 of the electricity: On the way of C1, R1, L1, R2 varistor, the primary power supply filter circuit, can input the instantaneous pressure filter, C2, R2, C4, C3 step-down circuit, L2 varistor and filter circuit is composed of rectifier, the filter, which can effectively protect the LED by high pressure breakdown.

Q:Hanging on the tree string lights, each one is 10 meters long, with a controller, I asked the factory with the AB protection, but the manufacturers say that only do the general anti rain, no water, even the rain stop, I want to use plastic wrap, don't know? Which expert can give advice and advice? emergency: You can use the plastic wrap, mouth down, so even if again under the rain is not bad. Or glue the entire controller to the point where the water is likely to enter the water.

Q:I want to do a string of LED lights that can use batteries. About 55 or so. The lights are 5MM blue. How can I work? Urgent urgent!!: If it is a general common blue LED working current is 20 mA, voltage of about 2.5V can be lit, the battery power can be used in parallel, the benefits of this connection is one of the damage does not influence the normal operation of other LED. And each LED string to a current limiting resistor, LED protection lamp, prolong life, calculation formula of the resistance for V / 0.02A=: voltage current resistance: 3V, battery powered =3 / 0.02=150. You want to supply 55 LED batteries to work together, the total current is up to 0.02x55=1.1A, i.e. 1AH (ah) capacity of the battery can work 1 hours or so.

Q:Led full-color light string and how to control wiring: Four line color data signal exposed lamp connected: lamp electrode with GND surface control signal is connected with the DAT clock with CLK

Q:How do you connect the LED lights?: A series of even parallel. Are not clear, boss, you want to use LED do what?There is a gap, which is the positive pole of the LED (usually the long foot is short and the foot is negative)

Q:Example: if I want to do a 40 head low voltage lamp string, do 10 lights, 1 loop, transformer is 150MA, then how can I calculate the resistance? The grid is 60 Hz of China's power grid! Give a formula, and then count the examples. What is it?! Thank you: Diode products cannot be calculated by resistors.

Q:How does the LED light string flash?: Because of the special volt ampere characteristics, LED can not use constant voltage driving mode, but is driven by cross flow. The direct drawback of cross flow drive, however, is heat. So people invented the drive mode of pulse drive. For example, 0.5 seconds per second, so that the amount of heat in the LED is reduced by half. Then turn the frequency up to 100 times per second, lighting for 0.005 seconds each time. At this point, the power of the LED is not the same, and people do not feel blinking. What's more, in this driving mode, an approximate cross flow drive (that is, the current is not necessarily precise) can be simplified, which simplifies the drive circuit (the precise cross flow source is very complex)

3. Manufacturer Capability
a)Trade Capacity
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range