Parker Flow Control Valve

Hot Products

Butterfly Valve with Plastic Handle Made in China on Sale

Butterfly Valve with Plastic Handle Made in China on Good Sale

Butterfly Valve Stainless Steel Threaded Directional on Sale Made in China

Butterfly Valve Made in China on Hot Sale with Good Quality

Air Evacuation Vent Valve for Solar Use Ash Silo Relief Valve

Butterfly Valve Plastic Handle Made in China on Hot Sale

Butterfly Valve Stainless Steel Threaded Directional with Plastic Handle

Butterfly Valve Made in China on Hot Sale

Butterfly Valve Stainless Steel Threaded Directional Made in China on Sale

Butterfly Valve Steel Threaded Directional with Plastic Handle

FAQ

How can the material be checked by valve approach? What experiments do you need?

(8) the throttle valve does not test the tightness of the closing parts, but the strength test and the tightness test of the stuffing and the gasket shall be carried out.(9) the pressure test, the valve closing force only allows a person's normal physical strength to close; not augmented with tools like leverage (except torque wrench), when the hand wheel diameter is greater than the wait at 320mm, allowing two common off.(10) with a sealed valve, should be taken out of packing for sealing test, sealed after the official closed, check whether leakage. When gas is used as a test, check the water in the stuffing box. When sealing test is carried out, the upper seal is not allowed to be in the tight position.(11) when the valve with drive device is tested and its tightness is tested, the sealing test shall be carried out by using the driving device to close the valve. For manual drive units, seal test shall also be done with the actuating closing valve.(12) the by-pass valve installed on the main valve after the strength test and the sealing test. The strength and tightness test of the main valve is carried out. The main valve should be opened when the closing member is opened.(13) iron valve strength test, the application of Pratia tapping valve and valve cover, check whether there is any leakage.(14) the valve test, in addition to the provisions of the plug valve to allow sealing surface oiling, other valves are not allowed in the sealing surface of the oil test.(15) when the valve pressure test, the blind plate on the valve pressure should not be too large, so as to avoid deformation of the valve, affecting the test results (cast iron valve if pressed too tight, will be damaged).(16) after the valve test pressure, should promptly remove the water and clean the valve, should also be prepared for the test record.

Valve connections - two how do different connections work?

The connection of two different connection forms is achieved by a transition conversion connector

How to better maintain the valve?

How to maintain the valve?Enter the same as other mechanical products, but also the need for maintenance. This work well, can extend the service life of the valve, the following will introduce the valve maintenanceStorage and maintenanceThe maintenance of the purpose is to keep the valve in the custody of the damage, or lower quality. In fact, improper storage is one of the important reasons for valve damageThe valve custody, should be arranged in good order, a small valve on the shelves, large valves can be neatly arranged in the warehouse on the ground, not arbitrary lumber pile, do not let the flange face contact with the ground. This is not only for beauty, mainly to protect the valve, not to touch badBecause the storage and handling properly, hand wheel broken, crooked stem touch the fixed nut hand wheel and stem loosening loss and so on, these should avoid unnecessary losses.We temporarily on the short-term use of the valve, should remove the asbestos packing, in order to avoid electrochemical corrosion damage to the valve stem.I just entered the library on the valve, to conduct inspections, such as during transport into the water or dirt to wipe clean, re storedThe import and export of valves to use wax paper or plastic sheet sealed to prevent dirt insideThe valves on the machined surface rust in the atmosphere should be coated with anti rust oil, protectI placed outside the valve, must be covered with linoleum or tarpaulins like rain, dust items. Keep the storage of the valve clean and dry

There is a rectangular hole in the valve core, which the heating company repairman gives to the bolt. Rest assured, I do not want to heating, but my indoor temperature is low, I suspect that the repairman mischief, deliberately give me lower temperature

The valve has a device like a cylinder lock that opens with a special key.The heating valve refers only to a radiator system accessories, is a type of valve, the valve commonly used heating system on the market is mainly divided into: gate valve, ball valve, safety valve, balance valve, globe valve, regulator valve, relief valve, pneumatic control valve.

How big valves are used in a DN159 pipe?

DN159 is the valve with the DN150 in the outer diameter of the pipe.The valve size of the pipeline is classified by nominal diameter:1, the small diameter valve: nominal diameter DN = 40mm valve.2, medium diameter valve: nominal diameter DN from 50 to 300mm valve.3, chase diameter valve: nominal valve DN for 350 ~ 1200mm valve.4, large diameter valve: nominal diameter DN = 1400mm valve.The components of the valve must be handled following process before they are assembled:1, according to processing requirements, some parts need polishing, surface processing burr can not be;2. All parts are degreased;3, after degreasing, pickling and passivation, the cleaning agent does not contain phosphorus;4. After pickling, rinse with pure water, no residue of medicament, and carbon steel parts shall be omitted;5, one by one parts with non-woven fabrics dry, not cable, hair and other retained parts of the surface, or with clean nitrogen drying;6, with non-woven fabrics or precision filter paper, stained with pure alcohol, wipe parts by one, until there is no dirty color.

What does valve J41H-16C mean?

J- stop valve4- flange type connection1- structure typeH- alloy steel seal16- nominal pressure 16 kgC- body carbon steel

I would like to ask how the valve entry, for a new pair, really difficult, what cutaway view, there are other, just contact the valve less than a week, and sometimes it is really difficult to understand. Forget the experienced teacher can be generous with your criticism to later, indebted forever, learn the valve Comrades some help.In a company CAD to relatives as soon as possible to a company, and then slowly improve, I do not know what is the request of the novice, and how to start as soon as possible, I am learning routine is: give me a set of valve design drawings, and then I paint it on, do not understand the structure and workshop look. I wonder if you have any good learning methods that can be referred to and supplemented by younger brother

I was about 08 years of contact valve, indeed many, but a company, all products will not have, are designed to do certain types of valves, such as for HVAC, or petrochemical, some other valves used in engineering, will do the purchase, so you only according to the company's products study on the line, need to learn what, what, high efficiency.If you do the design, you have to learn a lot of things: "mechanical design manual" and "valve design manual" is essential, often used;Of course, functional things are the basis, that is, the structure, the work principle must be obtained first, in order to do relevant design and improvement;First of all, the structure design, CAD must learn, three-dimensional software also have to learn one, Solidworks, Peo/E, UG, Catia can be;Second, strength analysis is necessary, so in mathematics, mechanics, mechanical design things to learn solid; can make strength analysis with finite element analysis software, need to learn, software Comosworks, Ansys;Third, the valve design will have fluid aspects, flow design, flow capacity, flow characteristics of the study, to study fluid mechanics, heat transfer, etc., CFD software has Fluent, Ansys, CFX, Star-CD;In addition, materials and technical aspects should be learned.Slowly, I also step by step by side with coming.Hope to be of help to you.

Automatic exhaust valve installed in the pipe before and after the installation of other valves need to press it?

Do not need ah, at most installed a gate valve, globe valve, and so on, installed on the exhaust valve on the line.